capthookb
27-01-07, 19:02
Χτες εκεί που δούλευαν όλα μια χαρά, ξαφνικά κόβεται η σύνδεση από το ίντερνετ. Κοιτάω τα λαμπάκια, αναμμένα κανονικά (Power,lan, adsl, και internet Leds). Πάω να μπώ στο web interface του router, τίποτα.... Ε λέω θα κόλλησε. Κάνω reset το router, επανεκιννεί κανονικά, συγχρονίζει τη γραμμή, συνδέεται με τον provider αλλά επαφή με το Pc καμία. Με hard reset τα ίδια. Ούτε Ping δεν κάνει. Ping από το pc στο router βγαίνει timeout. Ping από το router στο pc πάλι timeout.
Έχει κανείς καμιά ιδέα; Προσπάθησα να περάσω και με tftp κάποιο firmware αλλά είναι σαν να μην έχει ταμπουρωθεί στο καβούκι του και δεν απαντάει σε κανέναν :)
Δείτε και το Log της διαδικασίας boot του router:
PSPBoot1.2 rev: 0.22.17
(c) Copyright 2002-2004 Texas Instruments, Inc. All Rights Reserved.
FlashType:
No mac find, use default mac
mac_value: 00:14:BF:99:A7:2F
Press ESC for monitor... 521
(psbl)
boot order: f
boot file: mtd1
Booting...
Launching kernel decompressor.
Starting LZMA Uncompression Algorithm.
Copyright (C) 2003 Texas Instruments Incorporated; Copyright (C) 1999-2003 Igor Pavlov.
Compressed file is LZMA format.
Kernel decompressor was successful ... launching kernel.
LIN
X
tarted..ConfThiCPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 16kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.4.17_mvl21-malta-mips_fp_le (root@59-120-187-167.hinet-ip.hinet.net) (gcc version 2.95.3 20010315 (release/MontaVista)) #31 ¤» 10¤λ 28 00:23:15 CST 2006
Determined physical RAM map:
memory: 14000000 @ 00000000 (reserved)
memory: 00020000 @ 14000000 (ROM data)
memory: 00fe0000 @ 14020000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
.........boot_code Pspboot...........
..54....49....45....4e....56....30....2e....38....00....ff..
base address: b0010000
env size: 65536
ptr: b0010000
Kernel command line:
calculating r4koff... 000b71b0(750000)
CPU frequency 150.00 MHz
Calibrating delay loop... 149.91 BogoMIPS
Freeing Adam2 reserved memory [0x14001000,0x0001f000]
Memory: 13876k/16384k available (1888k kernel code, 2508k reserved, 139k data, 64k init)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
TI Optimizations: Allocating TI-Cached Memory Pool.
Warning: Number of buffers is not configured.Setting default to 512
Using 512 Buffers for TI-Cached Memory Pool.
DEBUG: Using Hybrid Mode.
NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.
Initializing RT netlink socket
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
ttyS01 at 0xa8610f00 (irq = 16) is a 16550A
Vlynq CONFIG_MIPS_AVALANCHE_VLYNQ_PORTS=2
Vlynq Device vlynq0 registered with minor no 63 as misc device. Result=0
Vlynq instance:0 Link UP
Vlynq Device vlynq1 registered with minor no 62 as misc device. Result=0
VLYNQ 1 : init failed
block: 64 slots per queue, batch=16
Using the MAC with external PHY
Cpmac driver is allocating buffer memory at init time.
Using the MAC with external PHY
Cpmac driver Disable TX complete interrupt setting threshold to 20.
Default Asymmetric MTU for eth0 1500
PPP generic driver version 2.4.1
avalanche flash device: 0x400000 at 0x10000000.
Amd/Fujitsu Extended Query Table v1.1 at 0x0040
Physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
Looking for mtd device :mtd0:
Found a mtd0 image (0xe0000), with size (0x2f0000).
Looking for mtd device :mtd1:
Found a mtd1 image (0x20000), with size (0x3b0000).
Looking for mtd device :mtd2:
Found a mtd2 image (0x0), with size (0x20000).
Looking for mtd device :mtd3:
Found a mtd3 image (0x3f0000), with size (0x10000).
Looking for mtd device :mtd4:
Found a mtd4 image (0x3d0000), with size (0x20000).
Creating 5 MTD partitions on "Physically mapped flash":
0x000e0000-0x003d0000 : "mtd0"
0x00020000-0x003d0000 : "mtd1"
0x00000000-0x00020000 : "mtd2"
0x003f0000-0x00400000 : "mtd3"
0x003d0000-0x003f0000 : "mtd4"
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 1024)
IPv4 over IPv4 tunneling driver
Default Asymmetric MTU for tunl0 1480
GRE over IPv4 tunneling driver
Default Asymmetric MTU for gre0 1476
Linux IP multicast router 0.06 plus PIM-SM
klips_info:ipsec_init: KLIPS startup, FreeS/WAN IPSec version: super-freeswan-1.99.8
Default Asymmetric MTU for ipsec0 0
Default Asymmetric MTU for ipsec1 0
Default Asymmetric MTU for ipsec2 0
Default Asymmetric MTU for ipsec3 0
Default Asymmetric MTU for ipsec4 0
klips_info:ipsec_alg_init: KLIPS alg v=0.8.1-0 (EALG_MAX=255, AALG_MAX=15)
klips_info:ipsec_alg_init: calling ipsec_alg_static_init()
ipsec_1des_init(alg_type=15 alg_id=2 name=1des): ret=0
You should NOT load 1DES support except for testing purposes !
ipsec_null_init(alg_type=15 alg_id=11 name=null): ret=0
ip_conntrack version 2.0 (128 buckets, 1024 max) - 392 bytes per conntrack
ip_tables: (c)2000 Netfilter core team
netfilter PSD loaded - (c) astaro AG
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Initializing the WAN Bridge.
Please set the MAC Address for the WAN Bridge.
Set the Environment variable 'wan_br_mac'.
MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
802.1Q VLAN Support v1.6 Ben Greear <greearb@candelatech.com>
vlan Initialization complete.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 64k freed
Firmware Version: 1.01.11
SQUASHFS error: Can't find a SQUASHFS superblock on mtdblock(31,4)
ret = -1
www -> /www
mount: Invalid argument
Hit enter to continue...killall: httpd: no process killed
Configured 19 states
now insmod tiatm
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/atm/tiatm.o
name=[eth0] lan_ifname=[br0]
=====> set br0 hwaddr to eth0
wlconf: No such file or directory
Lan Ipaddr: 255.255.255.0 Netmask: 255.255.255.0................
255.255.255.0 255.255.255.0
mixed mode
insmod ap driver
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/net/tiap.o
ret = 0
.............list ..............
antsel.c: Internal Antenna
[HTTPD Starting on /www]
The boot is UNKNOWN
tftp server started
tftpd: standalone socket
HTTPD start, port 80
dhcpd:auto_search_ip=0,firstsetlanip=1
.............list ..............
info, udhcp server (v0.9.8) started
˜QE: No such file or directory
log_ipaddr=255
killall: leijun--upnpd-igd ver 0.83 2004-0329: no process killed
Now Start syslog.........................!!zebra disabled
killall: adslpolling: no process killed
IDLE
Hit enter to continue...wan def hwaddr 00:14:BF:99:A7:30
polling now .......
upnpd-igd:current select wan connection:0
upnp_content_num_0 = 14
killall: begin_now: no process killed
BusyBox v0.60.0 (2006.10.27-16:28+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
#
#
όπως επίσης το output της ifconfig
# ifconfig[J
br0 Link encap:Ethernet HWaddr 00:14:BF:99:A7:2F
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:26 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:7623 (7.4 kb)
eth0 Link encap:Ethernet HWaddr 00:14:BF:99:A7:2F
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:6346 (6.1 kb)
Base address:0x2800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wlan0 Link encap:Ethernet HWaddr 00:14:BF:99:A7:2F
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:92 (92.0 b)
Έχει κανείς καμιά ιδέα του τι συμβαίνει;
Στο log βλέπω κάτι που με ανησυχεί πολύ:
SQUASHFS error: Can't find a SQUASHFS superblock on mtdblock(31,4)
Λέτε να είναι hardware το πρόβλημα;
Έχει κανείς καμιά ιδέα; Προσπάθησα να περάσω και με tftp κάποιο firmware αλλά είναι σαν να μην έχει ταμπουρωθεί στο καβούκι του και δεν απαντάει σε κανέναν :)
Δείτε και το Log της διαδικασίας boot του router:
PSPBoot1.2 rev: 0.22.17
(c) Copyright 2002-2004 Texas Instruments, Inc. All Rights Reserved.
FlashType:
No mac find, use default mac
mac_value: 00:14:BF:99:A7:2F
Press ESC for monitor... 521
(psbl)
boot order: f
boot file: mtd1
Booting...
Launching kernel decompressor.
Starting LZMA Uncompression Algorithm.
Copyright (C) 2003 Texas Instruments Incorporated; Copyright (C) 1999-2003 Igor Pavlov.
Compressed file is LZMA format.
Kernel decompressor was successful ... launching kernel.
LIN
X
tarted..ConfThiCPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 16kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.4.17_mvl21-malta-mips_fp_le (root@59-120-187-167.hinet-ip.hinet.net) (gcc version 2.95.3 20010315 (release/MontaVista)) #31 ¤» 10¤λ 28 00:23:15 CST 2006
Determined physical RAM map:
memory: 14000000 @ 00000000 (reserved)
memory: 00020000 @ 14000000 (ROM data)
memory: 00fe0000 @ 14020000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
.........boot_code Pspboot...........
..54....49....45....4e....56....30....2e....38....00....ff..
base address: b0010000
env size: 65536
ptr: b0010000
Kernel command line:
calculating r4koff... 000b71b0(750000)
CPU frequency 150.00 MHz
Calibrating delay loop... 149.91 BogoMIPS
Freeing Adam2 reserved memory [0x14001000,0x0001f000]
Memory: 13876k/16384k available (1888k kernel code, 2508k reserved, 139k data, 64k init)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
TI Optimizations: Allocating TI-Cached Memory Pool.
Warning: Number of buffers is not configured.Setting default to 512
Using 512 Buffers for TI-Cached Memory Pool.
DEBUG: Using Hybrid Mode.
NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.
Initializing RT netlink socket
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
ttyS01 at 0xa8610f00 (irq = 16) is a 16550A
Vlynq CONFIG_MIPS_AVALANCHE_VLYNQ_PORTS=2
Vlynq Device vlynq0 registered with minor no 63 as misc device. Result=0
Vlynq instance:0 Link UP
Vlynq Device vlynq1 registered with minor no 62 as misc device. Result=0
VLYNQ 1 : init failed
block: 64 slots per queue, batch=16
Using the MAC with external PHY
Cpmac driver is allocating buffer memory at init time.
Using the MAC with external PHY
Cpmac driver Disable TX complete interrupt setting threshold to 20.
Default Asymmetric MTU for eth0 1500
PPP generic driver version 2.4.1
avalanche flash device: 0x400000 at 0x10000000.
Amd/Fujitsu Extended Query Table v1.1 at 0x0040
Physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
Looking for mtd device :mtd0:
Found a mtd0 image (0xe0000), with size (0x2f0000).
Looking for mtd device :mtd1:
Found a mtd1 image (0x20000), with size (0x3b0000).
Looking for mtd device :mtd2:
Found a mtd2 image (0x0), with size (0x20000).
Looking for mtd device :mtd3:
Found a mtd3 image (0x3f0000), with size (0x10000).
Looking for mtd device :mtd4:
Found a mtd4 image (0x3d0000), with size (0x20000).
Creating 5 MTD partitions on "Physically mapped flash":
0x000e0000-0x003d0000 : "mtd0"
0x00020000-0x003d0000 : "mtd1"
0x00000000-0x00020000 : "mtd2"
0x003f0000-0x00400000 : "mtd3"
0x003d0000-0x003f0000 : "mtd4"
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 1024)
IPv4 over IPv4 tunneling driver
Default Asymmetric MTU for tunl0 1480
GRE over IPv4 tunneling driver
Default Asymmetric MTU for gre0 1476
Linux IP multicast router 0.06 plus PIM-SM
klips_info:ipsec_init: KLIPS startup, FreeS/WAN IPSec version: super-freeswan-1.99.8
Default Asymmetric MTU for ipsec0 0
Default Asymmetric MTU for ipsec1 0
Default Asymmetric MTU for ipsec2 0
Default Asymmetric MTU for ipsec3 0
Default Asymmetric MTU for ipsec4 0
klips_info:ipsec_alg_init: KLIPS alg v=0.8.1-0 (EALG_MAX=255, AALG_MAX=15)
klips_info:ipsec_alg_init: calling ipsec_alg_static_init()
ipsec_1des_init(alg_type=15 alg_id=2 name=1des): ret=0
You should NOT load 1DES support except for testing purposes !
ipsec_null_init(alg_type=15 alg_id=11 name=null): ret=0
ip_conntrack version 2.0 (128 buckets, 1024 max) - 392 bytes per conntrack
ip_tables: (c)2000 Netfilter core team
netfilter PSD loaded - (c) astaro AG
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Initializing the WAN Bridge.
Please set the MAC Address for the WAN Bridge.
Set the Environment variable 'wan_br_mac'.
MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
802.1Q VLAN Support v1.6 Ben Greear <greearb@candelatech.com>
vlan Initialization complete.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 64k freed
Firmware Version: 1.01.11
SQUASHFS error: Can't find a SQUASHFS superblock on mtdblock(31,4)
ret = -1
www -> /www
mount: Invalid argument
Hit enter to continue...killall: httpd: no process killed
Configured 19 states
now insmod tiatm
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/atm/tiatm.o
name=[eth0] lan_ifname=[br0]
=====> set br0 hwaddr to eth0
wlconf: No such file or directory
Lan Ipaddr: 255.255.255.0 Netmask: 255.255.255.0................
255.255.255.0 255.255.255.0
mixed mode
insmod ap driver
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/net/tiap.o
ret = 0
.............list ..............
antsel.c: Internal Antenna
[HTTPD Starting on /www]
The boot is UNKNOWN
tftp server started
tftpd: standalone socket
HTTPD start, port 80
dhcpd:auto_search_ip=0,firstsetlanip=1
.............list ..............
info, udhcp server (v0.9.8) started
˜QE: No such file or directory
log_ipaddr=255
killall: leijun--upnpd-igd ver 0.83 2004-0329: no process killed
Now Start syslog.........................!!zebra disabled
killall: adslpolling: no process killed
IDLE
Hit enter to continue...wan def hwaddr 00:14:BF:99:A7:30
polling now .......
upnpd-igd:current select wan connection:0
upnp_content_num_0 = 14
killall: begin_now: no process killed
BusyBox v0.60.0 (2006.10.27-16:28+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
#
#
όπως επίσης το output της ifconfig
# ifconfig[J
br0 Link encap:Ethernet HWaddr 00:14:BF:99:A7:2F
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:26 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:7623 (7.4 kb)
eth0 Link encap:Ethernet HWaddr 00:14:BF:99:A7:2F
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:6346 (6.1 kb)
Base address:0x2800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wlan0 Link encap:Ethernet HWaddr 00:14:BF:99:A7:2F
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:92 (92.0 b)
Έχει κανείς καμιά ιδέα του τι συμβαίνει;
Στο log βλέπω κάτι που με ανησυχεί πολύ:
SQUASHFS error: Can't find a SQUASHFS superblock on mtdblock(31,4)
Λέτε να είναι hardware το πρόβλημα;