nfotis
11-04-07, 12:03
Καλημέρα σε όλους,
δουλεύω σαν τεχνικός σε μια εταιρεία, και (μετά από μία δεκαετία μακριά από Cisco) προέκυψε η ανάγκη να στήσω έναν 876, καθώς ο αρμόδιος τεχνικός δεν βρίσκει άκρη με το SDM (αν και υποψιάζομαι πρόβλημα hardware).
Από ότι καταλαβαίνω, κάτι δεν πάει καλά ανάμεσα στο Netmod S0 και την ISDN σύνδεση του Cisco, καθώς το λαμπάκι LNK είναι μεν αναμμένο, αλλά το CD αναβοσβήνει συνέχεια (πριν βάλω ένα UTP RJ-45 patch cable, και το LNK αναβόσβηνε).
Cisco#sh isdn status
Global ISDN Switchtype = basic-net3
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = basic-net3
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 65, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x80000003
Total Allocated ISDN CCBs = 0
Router#sh isdn history
-------------------------------------------------------------------------------
ISDN CALL HISTORY
--------------------------------------------------------------------------------
Call Calling Called Remote Seconds Seconds Seconds Charges
Type Number Number Name Used Left Idle Units/Currency
--------------------------------------------------------------------------------
Διαισθάνομαι ότι ναι μεν έχει επικοινωνία με το ISDN, αλλά δεν σηκώνει κανένα από τα κανάλια όταν πάω να καλέσω.
Δοκίμασα και την εντολή
isdn test call interface bRI 0 8962577777 speed 64 number-of-calls 10
αλλά τζίφος.
Παραθέτω και τα στοιχεία του μηχανήματος, μπας κι έχετε καμιά ιδέα:
#sh version
Cisco IOS Software, C870 Software (C870-ADVSECURITYK9-M), Version 12.4(4)T7, RELEASE SOFTWARE (fc1)
Compiled Wed 29-Nov-06 00:43 by kellythw
ROM: System Bootstrap, Version 12.3(8r)YI3, RELEASE SOFTWARE
Router uptime is 3 hours, 46 minutes
System returned to ROM by power-on
System image file is "flash:c870-advsecurityk9-mz.124-4.T7.bin"
Cisco 876 (MPC8272) processor (revision 0x200) with 118784K/12288K bytes of memory.
Processor board ID FCZ110922W8
MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
4 FastEthernet interfaces
1 ISDN Basic Rate interface
1 ATM interface
128K bytes of non-volatile configuration memory.
24576K bytes of processor board System flash (Intel Strataflash)
Configuration register is 0x2102
Παρακάτω παραθέτω τμήματα από το running-config (πρόσθεσα έναν dialer για το ATM interface, που αυτή τη στιγμή είναι ανενεργό, καθώς το Cisco θα πάει σε υποκατάστημα της εταιρείας μας, και θέλουμε να δουλέψουμε σε πρώτη φάση με το ISDN interface).
Εχω βγάλει απέξω τα σχετικά με VPN, γιατί μάλλον δεν αφορούνε το θέμα μας σε αυτή τη φάση.
Router#sh running-config
Building configuration...
Current configuration : 5191 bytes
!
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
!
hostname Router
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 debugging
logging console critical
enable secret 5 $1$IJz5$odxhV0kRGvIHJvNwiaBz/1
!
aaa new-model
!
!
aaa authentication login default local
aaa authorization exec default local
!
aaa session-id common
!
resource policy
!
clock timezone PCTime 2
clock summer-time PCTime date Mar 30 2003 3:00 Oct 26 2003 4:00
ip subnet-zero
no ip source-route
ip cef
!
!
ip tcp synwait-time 10
no ip bootp server
ip domain name yourdomain.com
ip name-server 194.30.220.119
ip name-server 194.30.220.117
ip ssh time-out 60
ip ssh authentication-retries 2
!
!
isdn switch-type basic-net3
!
....
!
interface BRI0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
encapsulation ppp
ip route-cache flow
dialer pool-member 1
isdn switch-type basic-net3
isdn point-to-point-setup
no cdp enable
!
interface ATM0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip route-cache flow
shutdown
atm vc-per-vp 64
no atm ilmi-keepalive
pvc 0/35
pppoe-client dial-pool-number 1
!
!
dsl operating-mode auto
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$$FW_INSIDE$
ip address 10.1.1.23 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly
ip route-cache flow
!
interface Dialer0
ip address negotiated
encapsulation ppp
dialer pool 1
dialer string 8962577777
dialer-group 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname username
ppp chap password 7 xxxxxx
ppp pap sent-username username password 7 xxxx
interface Dialer1
description connection to Internet via HOL
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
no ip split-horizon
dialer in-band
dialer idle-timeout 60
dialer fast-idle 30
dialer string 8962577777
dialer hold-queue 10
dialer-group 1
no cdp enable
ppp authentication pap chap callin
ppp chap hostname username
ppp chap password 7 xxx
ppp pap sent-username username password 7 xxx
!
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
!
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 1 interface Dialer1 overload
!
logging trap debugging
access-list 100 remark SDM_ACL Category=4
access-list 100 permit gre host 10.1.3.1 host 62.38.174.34
dialer-list 1 protocol ip permit
no cdp run
!
control-plane
!
!
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
!
line con 0
no modem enable
transport output telnet
line aux 0
transport output telnet
line vty 0 4
transport input telnet ssh
!
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
end
Ευχαριστώ προκαταβολικά για όποια βοήθεια και ιδέες μπορείτε να δώσετε.
Νικόλαος Φώτης
δουλεύω σαν τεχνικός σε μια εταιρεία, και (μετά από μία δεκαετία μακριά από Cisco) προέκυψε η ανάγκη να στήσω έναν 876, καθώς ο αρμόδιος τεχνικός δεν βρίσκει άκρη με το SDM (αν και υποψιάζομαι πρόβλημα hardware).
Από ότι καταλαβαίνω, κάτι δεν πάει καλά ανάμεσα στο Netmod S0 και την ISDN σύνδεση του Cisco, καθώς το λαμπάκι LNK είναι μεν αναμμένο, αλλά το CD αναβοσβήνει συνέχεια (πριν βάλω ένα UTP RJ-45 patch cable, και το LNK αναβόσβηνε).
Cisco#sh isdn status
Global ISDN Switchtype = basic-net3
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = basic-net3
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 65, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x80000003
Total Allocated ISDN CCBs = 0
Router#sh isdn history
-------------------------------------------------------------------------------
ISDN CALL HISTORY
--------------------------------------------------------------------------------
Call Calling Called Remote Seconds Seconds Seconds Charges
Type Number Number Name Used Left Idle Units/Currency
--------------------------------------------------------------------------------
Διαισθάνομαι ότι ναι μεν έχει επικοινωνία με το ISDN, αλλά δεν σηκώνει κανένα από τα κανάλια όταν πάω να καλέσω.
Δοκίμασα και την εντολή
isdn test call interface bRI 0 8962577777 speed 64 number-of-calls 10
αλλά τζίφος.
Παραθέτω και τα στοιχεία του μηχανήματος, μπας κι έχετε καμιά ιδέα:
#sh version
Cisco IOS Software, C870 Software (C870-ADVSECURITYK9-M), Version 12.4(4)T7, RELEASE SOFTWARE (fc1)
Compiled Wed 29-Nov-06 00:43 by kellythw
ROM: System Bootstrap, Version 12.3(8r)YI3, RELEASE SOFTWARE
Router uptime is 3 hours, 46 minutes
System returned to ROM by power-on
System image file is "flash:c870-advsecurityk9-mz.124-4.T7.bin"
Cisco 876 (MPC8272) processor (revision 0x200) with 118784K/12288K bytes of memory.
Processor board ID FCZ110922W8
MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
4 FastEthernet interfaces
1 ISDN Basic Rate interface
1 ATM interface
128K bytes of non-volatile configuration memory.
24576K bytes of processor board System flash (Intel Strataflash)
Configuration register is 0x2102
Παρακάτω παραθέτω τμήματα από το running-config (πρόσθεσα έναν dialer για το ATM interface, που αυτή τη στιγμή είναι ανενεργό, καθώς το Cisco θα πάει σε υποκατάστημα της εταιρείας μας, και θέλουμε να δουλέψουμε σε πρώτη φάση με το ISDN interface).
Εχω βγάλει απέξω τα σχετικά με VPN, γιατί μάλλον δεν αφορούνε το θέμα μας σε αυτή τη φάση.
Router#sh running-config
Building configuration...
Current configuration : 5191 bytes
!
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
!
hostname Router
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 debugging
logging console critical
enable secret 5 $1$IJz5$odxhV0kRGvIHJvNwiaBz/1
!
aaa new-model
!
!
aaa authentication login default local
aaa authorization exec default local
!
aaa session-id common
!
resource policy
!
clock timezone PCTime 2
clock summer-time PCTime date Mar 30 2003 3:00 Oct 26 2003 4:00
ip subnet-zero
no ip source-route
ip cef
!
!
ip tcp synwait-time 10
no ip bootp server
ip domain name yourdomain.com
ip name-server 194.30.220.119
ip name-server 194.30.220.117
ip ssh time-out 60
ip ssh authentication-retries 2
!
!
isdn switch-type basic-net3
!
....
!
interface BRI0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
encapsulation ppp
ip route-cache flow
dialer pool-member 1
isdn switch-type basic-net3
isdn point-to-point-setup
no cdp enable
!
interface ATM0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip route-cache flow
shutdown
atm vc-per-vp 64
no atm ilmi-keepalive
pvc 0/35
pppoe-client dial-pool-number 1
!
!
dsl operating-mode auto
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$$FW_INSIDE$
ip address 10.1.1.23 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly
ip route-cache flow
!
interface Dialer0
ip address negotiated
encapsulation ppp
dialer pool 1
dialer string 8962577777
dialer-group 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname username
ppp chap password 7 xxxxxx
ppp pap sent-username username password 7 xxxx
interface Dialer1
description connection to Internet via HOL
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
no ip split-horizon
dialer in-band
dialer idle-timeout 60
dialer fast-idle 30
dialer string 8962577777
dialer hold-queue 10
dialer-group 1
no cdp enable
ppp authentication pap chap callin
ppp chap hostname username
ppp chap password 7 xxx
ppp pap sent-username username password 7 xxx
!
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
!
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 1 interface Dialer1 overload
!
logging trap debugging
access-list 100 remark SDM_ACL Category=4
access-list 100 permit gre host 10.1.3.1 host 62.38.174.34
dialer-list 1 protocol ip permit
no cdp run
!
control-plane
!
!
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
!
line con 0
no modem enable
transport output telnet
line aux 0
transport output telnet
line vty 0 4
transport input telnet ssh
!
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
end
Ευχαριστώ προκαταβολικά για όποια βοήθεια και ιδέες μπορείτε να δώσετε.
Νικόλαος Φώτης