PDA

Επιστροφή στο Forum : Περί ROS ο λόγος...



Σελίδες : 1 2 3 4 5 6 7 8 9 10 11 [12] 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

deniSun
13-04-21, 14:15
What's new in 6.48.2 (2021-Apr-09 10:17):


*) bonding - improved system stability when disabling/enabling bonding ports;
*) bridge - improved bridge stability when host changes port (introduced in v6.47);
*) console - require "write+ftp" permissions for exporting configuration to file;
*) console - updated copyright notice;
*) crs3xx - added "/system swos" menu for CRS354 devices, should only be used after SwOS 2.13 release;
*) crs3xx - fixed interface LEDs for QSFP+ and SFP+ interfaces on CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - fixed packet transmit in 5Gbps link rate for CRS312 device;
*) crs3xx - improved 1Gbps Ethernet port group traffic forwarding for CRS354 devices;
*) dhcp - fixed link state checking for DHCP client;
*) ethernet - fixed cable-test for some devices (e.g. RB2011, RB951G-2HnD);
*) ethernet - improved system stability when receiving large VLAN tagged packets on IPQ4018/IPQ4019 devices;
*) fastpath - fixed IP packet receive on bridge and bonding interfaces when destination MAC address match with slave port MAC;
*) health - fixed voltage monitor on BaseBox5 devices;
*) ike2 - added "MS-CHAP-Domain" attribute to RADIUS requests;
*) ike2 - fixed DH group negotiation with EAP;
*) ike2 - fixed EAP MSK length validation (introduced in v6.48);
*) ike2 - fixed initial traffic selector's protocol and port in transport mode;
*) ipv6 - improved system stability when parsing IPv6 options;
*) lora - added additional predefined network servers;
*) lora - added option to hide CRC error messages in monitor;
*) lora - improved downlink transmission;
*) ospf - fixed type-7 LSA translation to type-5;
*) ovpn - fixed route cache entry leak when establishing a new session;
*) poe - do not perform PoE firmware upgrade procedure on RB960 and OmniTik devices without PoE out;
*) ppp - do not fail "at-chat" command when issued on disabled PPP interface;
*) ptp - improved management service stability when receiving bogus packets;
*) quickset - prefer 5GHz interface for WiFi scan in CPE mode;
*) rb3011 - improved system stability when changing RouterBOARD settings (introduced in v6.48);
*) snmp - fixed SNMP trap agent address;
*) supout - fixed "topic" column presence in "Log" section;
*) switch - improved resource allocation on 98PX1012 switch chip for CCR2004-1G-12S+2XS device;
*) switch - improved system stability with 98PX1012 switch chip for CCR2004-1G-12S+2XS device;
*) telnet - do not send options if connecting to non standard port;
*) telnet - fixed server when run on non standard port;
*) tr069-client - improved management service stability when receiving bogus packets;
*) upgrade - fixed upgrade procedure on 16MB devices;
*) upgrade - improved "long-term" upgrade procedure on SMIPS devices;
*) user - fixed "skin" configuration for user groups (introduced in v6.48);
*) webfig - allow to specify "prefix" parameter under "IPv6/ND/Prefixes" menu;
*) webfig - do not corrupt settings when starting "Wireless Sniffer";
*) webfig - do not move top right menu in opposite direction when scrolling horizontally;
*) webfig - do not show newly created SMB shares as invalid;
*) webfig - fixed new interface addition;
*) webfig - show "Interfaces" menu by default after logging in;
*) webfig - show "network-mode" for LTE modems that support it;
*) winbox - added "Channel" parameter under "System/Console" menu;
*) winbox - do not show empty "CPU Frequency" parameter under "System/Resources" menu;
*) winbox - fixed "reachable-time" value unit under "IPv6/ND" menu;
*) winbox - fixed QCA-8511 switch chip type reporting under "Switch/Settings" menu;
*) winbox - fixed duplicate "Trusted" setting under "Interface/Bridge/Ports" menu;
*) winbox - hide "Allow Roaming" parameter on LTE modems that do not support it;
*) winbox - increased "target" field limit to 128 under "Queues" menu;
*) winbox - renamed IP protocol 41 to "ipv6-encap";
*) winbox - show "LCD" only on boards that have LCD;
*) winbox - show "System/Health" only on boards that have health monitoring;
*) winbox - show "activity" column by default under "IP/Kid Control/Devices" menu;

Kostinos
17-04-21, 15:48
Πάντως εμένα μου έκανε εντύπωση 6.48.1
κι μετά βγάλανε 6.48.2 περίμενα να βγει η έκδοση 6.49.** ξέρουμε τι πλεονεκτήματα προσφέρει η είναι βέλτιώσεις του προηγούμενου patch;;;

deniSun
17-04-21, 17:15
Υπάρχει το changelog.

deniSun
12-05-21, 16:48
6.49beta44 changelog:
Changes in this release:


*) bridge - fixed "vlan-encap" setting for filter and NAT rules;
*) crs3xx - fixed Ethernet LEDs after reboot for CRS354 devices;
*) health - added "phy-temperature" sensor monitoring for CRS312 device;
*) ike2 - added "MS-CHAP-Domain" attribute to RADIUS requests;
*) lte - fixed "earfcn" to band translation for "cell-monitor";
*) switch - fixed (R/M)STP port blocking right before switching them in HW bridge (fixes possible packet loop when changing bridge settings);
*) tile - fixed bridge performance degradation (introduced in v6.47);
*) winbox - show "System/Health" only on boards that have health monitoring;
*) wireless - improved system stability on several 802.11ac devices (introduced in v6.49beta36);
*) wireless - improve signaling of QCA9984 interface capabilities when using 160/80+80MHz channel width;
*) www - added "X-Frame-Options" header information to disallow website embedding in other pages;

deniSun
19-05-21, 14:14
6.49beta46 changelog:
Changes in this release:


!) wireless - fixed all affecting 'FragAttacks' vulnerabilities (CVE-2020-24587, CVE-2020-24588, CVE-2020-26144, CVE-2020-26146, CVE-2020-26147);
*) crs3xx - fixed packet forwarding on 1Gbps Ethernet interfaces for CRS354 devices (introduced in v6.49beta44);
*) dns - fixed CNAME query when target record is not in cache;
*) winbox - fixed health reporting on RB960, hEX, hEX S and hAP ac3 devices;

Other changes since v6.48.2:

*) bridge - added IGMP and MLD querier monitoring (CLI only);
*) bridge - added IGMP snooping log when multicast table gets full;
*) bridge - added MAC and IP source addresses information for DHCP snooping log;
*) bridge - fixed "vlan-encap" setting for filter and NAT rules;
*) bridge - improved system stability when disabling IGMP/MLD querier port (introduced in v6.49beta22);
*) bridge - improved system stability when using IGMP snooping and changing bridge MAC address;
*) chr - fixed OS provisioning on Azure;
*) chr - improved stability when changing "flow-control" settings on interfaces with e1000 drivers;
*) conntrack - increased total connection tracking table size based on installed RAM size;
*) console - require "write+ftp" permissions for executing script to file;
*) console - require "write+ftp" permissions for printing to file;
*) crs3xx - correctly filter packets by L2MTU on 1Gbps Ethernet interfaces for CRS354 devices;
*) crs3xx - fixed Ethernet LEDs after reboot for CRS354 devices;
*) crs3xx - fixed LEDs for QSFP+ interface on CRS326-24S+2Q+ device;
*) crs3xx - fixed SFP and SFP+ link rate reporting (introduced in v6.48beta11);
*) crs3xx - fixed VLAN priority removal for CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - fixed interface flow control;
*) crs3xx - fixed port-isolation on bonding interfaces for CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - improved LACP linking between CRS3xx series switches;
*) crs3xx - improved QSFP+ linking and mode changing for CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - improved packet transmit on SFP+ interfaces;
*) crs3xx - improved switch resource allocation for CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - improved system stability when receiving large frames on CPU for CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) defconf - fixed default configuration loading on RBOmniTikPG-5HacD;
*) defconf - fixed minor typo in configuration description;
*) defconf - removed overlapping IPv6 firewall rules;
*) defconf - use router as DNS server for DHCP hosts;
*) dhcpv6-server - check if pool name has changed from RADIUS on renew;
*) dhcpv6-server - improved dynamic server entry update;
*) dot1x - fixed "reject-vlan-id" for MAC authentication (introduced in v6.48);
*) dot1x - fixed MAC authentication fallback (introduced in v6.48);
*) firewall - fixed "ingress-priority" matcher;
*) firewall - fixed GRE protocol packets considered invalid when PPTP helper is disabled;
*) health - added "phy-temperature" sensor monitoring for CRS312 device;
*) ike2 - added "MS-CHAP-Domain" attribute to RADIUS requests;
*) ike2 - added support for ASN.1 DN "my-id" value setting for initiators;
*) ike2 - fixed initiator packet retransmit with DDOS cookie;
*) ipsec - fixed SA address parameter exporting;
*) ipsec - improved system stability on CHR;
*) ipsec - improved system stability on MMIPS devices;
*) lte - fixed "earfcn" to band translation for "cell-monitor";
*) m33g - removed 12..16 pins from "/system gpio" menu;
*) mipsbe - improved booting speed on non-NAND devices ("/system routerboard upgrade" required);
*) netinstall - fixed lock file persistence after reinstall;
*) netinstall - improved bootp packet handling on Linux netinstall-cli version when multiple NIC's are present;
*) ntp - use correct IPv6 multicast group for SNTP client;
*) package - always allow to uninstall package even if there is no free disk space left;
*) poe - fixed PoE out functionality on CRS354 (introduced in v6.49beta22);
*) ppp - improved stability when receiving bogus response on modem channel;
*) rb4011 - fixed SFP+ port MTU setting after link state change;
*) rb4011 - improved SFP+ port stability after boot-up;
*) rb922 - fixed miniPCI-e card detection (introduced in v6.49beta11);
*) route - improved stability when connected route is modified;
*) sfp - added "sfp-rate-select" setting (CLI only);
*) sfp - fixed GPON module linking (introduced in v6.47);
*) sfp - improved cable length monitoring as defined per SFF-8472 and SFF-8636;
*) sfp - improved link stability for 10G, 25G and 40G modules on CRS309, CRS312, CRS326-24S+2Q+ CRS354 and CCR2004 devices;
*) ssh - return proper error code from executed command;
*) supout - print detailed list of active user sessions;
*) switch - fixed (R/M)STP port blocking right before switching them in HW bridge (fixes possible packet loop when changing bridge settings);
*) switch - improved packet transmit between CPU and 98PX1012 for CCR2004-1G-12S+2XS device;
*) swos - fixed "static-ip-address" parameter;
*) system - improved resource allocation (improves several service stability e.g. HTTPS, PPPoE, VPN);
*) tile - fixed bridge performance degradation (introduced in v6.47);
*) tr069-client - added "X_MIKROTIK_LinkDowns" parameter for interface "link-downs" value reporting;
*) upgrade - fixed free space checking on flash type memories when installing new packages;
*) w60g - improved stability in low temperature environments;
*) webfig - do not show value units twice;
*) webfig - fixed "PortMapping" button (introduced in v6.48.2);
*) webfig - fixed "Wireless/CAP" menu opening;
*) webfig - fixed interface sorting by name;
*) webfig - show only "Close" button under "Wireless/Wireless Sniffer/Sniffed Packets" menu;
*) winbox - added "interface-speed-100G" LED type to "System/LEDs" menu;
*) winbox - fixed support for "Delegated-IPv6-Prefix" for PPP services;
*) winbox - show "System/Health" only on boards that have health monitoring;
*) wireless - do not send packet back to station-bridge it was received from;
*) wireless - fixed issue with multicast traffic delivery to client devices using power-save;
*) wireless - fixed minor typo in debug logging messages;
*) wireless - improve WMM priority assignment for packets with internal priority greater than 7;
*) wireless - improve regulatory compliance with DFS requirements;
*) wireless - improve signaling of QCA9984 interface capabilities when using 160/80+80MHz channel width;
*) wireless - improved system stability on several 802.11ac devices (introduced in v6.49beta36);
*) wireless - renamed "secondary-channel" to "secondary-frequency";
*) wireless - updated "united kingdom" regulatory domain information;
*) www - added "X-Frame-Options" header information to disallow website embedding in other pages;

deniSun
26-05-21, 12:43
6.48.3 changelog:

MAJOR CHANGES IN v6.48.3:
----------------------
!) wireless - fixed all affecting 'FragAttacks' vulnerabilities (CVE-2020-24587, CVE-2020-24588, CVE-2020-26144, CVE-2020-26146, CVE-2020-26147);
----------------------

*) branding - added option to upload custom files (newly generated branding package required);
*) console - do not clear environment values if any global variable is set;
*) crs3xx - fixed Ethernet LEDs after reboot for CRS354 devices;
*) crs3xx - fixed VLAN priority removal for CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - fixed port-isolation on bonding interfaces for CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - improved LACP linking between CRS3xx series switches;
*) crs3xx - improved system stability when receiving large frames on CPU for CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) defconf - fixed default configuration loading on RBOmniTikPG-5HacD;
*) dot1x - fixed "reject-vlan-id" for MAC authentication (introduced in v6.48);
*) dot1x - fixed MAC authentication fallback (introduced in v6.48);
*) ipsec - fixed SA address parameter exporting;
*) lte - fixed "earfcn" to band translation for "cell-monitor";
*) package - added new "iot" package with Bluetooth (KNOT only) and MQTT publisher support;
*) rb4011 - fixed SFP+ port MTU setting after link state change;
*) rb4011 - improved SFP+ port stability after boot-up;
*) route - improved stability when connected route is modified;
*) sfp - improved cable length monitoring as defined per SFF-8472 and SFF-8636;
*) ssh - return proper error code from executed command;
*) system - improved resource allocation (improves several service stability e.g. HTTPS, PPPoE, VPN);
*) tile - fixed bridge performance degradation (introduced in v6.47);
*) webfig - fixed "PortMapping" button (introduced in v6.48.2);
*) winbox - fixed health reporting on RB960, hEX and hEX S devices;
*) winbox - show "System/Health" only on boards that have health monitoring;
*) wireless - fixed issue with multicast traffic delivery to client devices using power-save;
*) wireless - improved iOS compatibility with HotSpot 2.0 networks;
*) www - added "X-Frame-Options" header information to disallow website embedding in other pages;

BillyVan
26-05-21, 19:51
Για κλάματα τα πακετα arm cpu ήταν χτυπημένα.

Τα εφτιαξαν μετα απο κραξιμο που έπεσε...

Εχω μεγαλη απογοήτευση απο αυτους.

deniSun
26-05-21, 21:03
Για κλάματα τα πακετα arm cpu ήταν χτυπημένα.

Τα εφτιαξαν μετα απο κραξιμο που έπεσε...

Εχω μεγαλη απογοήτευση απο αυτους.

Εγώ το κατέβασα σχεδόν μόλις βγήκε και δεν είχε θέμα.

BillyVan
26-05-21, 23:31
Εγώ το κατέβασα σχεδόν μόλις βγήκε και δεν είχε θέμα.

Το προβλημα το ειχαν τα ξεχωριστα πακετα για τους arm.

Το zip με ολα τα ξεχωριστα services δηλαδη.

Εγινε λιγο κλάμα αλλα το διορθωσαν άμεσα.

Μαλλον εσυ περασες το 1 αρχειο της αναβαθμισης με ολα τα πακετα που δεν ειχε θεμα.

deniSun
27-05-21, 12:33
Το προβλημα το ειχαν τα ξεχωριστα πακετα για τους arm.

Το zip με ολα τα ξεχωριστα services δηλαδη.

Εγινε λιγο κλάμα αλλα το διορθωσαν άμεσα.

Μαλλον εσυ περασες το 1 αρχειο της αναβαθμισης με ολα τα πακετα που δεν ειχε θεμα.

Χρησιμοποιώ ntp οπότε κατεβάζω και το extra zip που το έχει.
Γι αυτό το αρχείο σου λέω ότι δεν είχα πρόβλημα.

deniSun
02-06-21, 17:19
6.47.10 changelog:

MAJOR CHANGES IN v6.47.10:
----------------------
!) wireless - fixed all affecting 'FragAttacks' vulnerabilities (CVE-2020-24587, CVE-2020-24588, CVE-2020-26144, CVE-2020-26146, CVE-2020-26147);
----------------------

*) bonding - improved system stability when disabling/enabling bonding ports;
*) branding - added option to upload custom files (newly generated branding package required);
*) capsman - use proper units for "ap-tx-limit" and "client-tx-limit" parameters;
*) console - do not clear environment values if any global variable is set;
*) console - require "write+ftp" permissions for exporting configuration to file;
*) console - updated copyright notice;
*) crs3xx - added "/system swos" menu for CRS354 devices, should only be used after SwOS 2.13 release;
*) crs3xx - fixed interface LEDs for QSFP+ and SFP+ interfaces on CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - improved 1Gbps Ethernet port group traffic forwarding for CRS354 devices;
*) crs3xx - improved system stability when receiving large frames on CPU for CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) defconf - fixed default configuration loading on LHG R;
*) defconf - fixed default configuration loading on RBOmniTikPG-5HacD;
*) dhcp - fixed link state checking for DHCP client;
*) dude - fixed configuration menu presence on ARM64 devices;
*) ethernet - improved system stability when receiving large VLAN tagged packets on IPQ4018/IPQ4019 devices;
*) ipsec - fixed SA address parameter exporting;
*) lte - fixed "earfcn" to band translation for "cell-monitor";
*) ovpn - fixed route cache entry leak when establishing a new session;
*) poe - do not perform PoE firmware upgrade procedure on RB960 and OmniTik devices without PoE out;
*) ppp - do not fail "at-chat" command when issued on disabled PPP interface;
*) ptp - improved management service stability when receiving bogus packets;
*) quickset - prefer 5GHz interface for WiFi scan in CPE mode;
*) rb4011 - fixed SFP+ port MTU setting after link state change;
*) rb4011 - improved SFP+ port stability after boot-up;
*) route - improved stability when connected route is modified;
*) sfp - improved cable length monitoring as defined per SFF-8472 and SFF-8636;
*) supout - fixed "topic" column presence in "Log" section;
*) switch - improved system stability with 98PX1012 switch chip for CCR2004-1G-12S+2XS device;
*) system - improved resource allocation (improves several service stability e.g. HTTPS, PPPoE, VPN);
*) telnet - do not send options if connecting to non standard port;
*) telnet - fixed server when run on non standard port;
*) tile - fixed bridge performance degradation (introduced in v6.47);
*) tr069-client - improved management service stability when receiving bogus packets;
*) upgrade - improved "long-term" upgrade procedure on SMIPS devices;
*) webfig - allow to specify "prefix" parameter under "IPv6/ND/Prefixes" menu;
*) webfig - do not corrupt settings when starting "Wireless Sniffer";
*) webfig - do not move top right menu in opposite direction when scrolling horizontally;
*) webfig - show "network-mode" for LTE modems that support it;
*) winbox - do not show "network-mode" parameter for LTE interfaces that do not support it;
*) winbox - do not show empty "CPU Frequency" parameter under "System/Resources" menu;
*) winbox - fixed "reachable-time" value unit under "IPv6/ND" menu;
*) winbox - fixed QCA-8511 switch chip type reporting under "Switch/Settings" menu;
*) winbox - fixed health reporting on RB960, hEX and hEX S devices;
*) winbox - hide "Allow Roaming" parameter on LTE modems that do not support it;
*) winbox - increased "target" field limit to 128 under "Queues" menu;
*) winbox - show "LCD" only on boards that have LCD;
*) winbox - show "System/Health" only on boards that have health monitoring;
*) winbox - show "activity" column by default under "IP/Kid Control/Devices" menu;
*) wireless - fixed issue with multicast traffic delivery to client devices using power-save;
*) wireless - improved iOS compatibility with HotSpot 2.0 networks;
*) www - added "X-Frame-Options" header information to disallow website embedding in other pages;

BillyVan
02-06-21, 18:41
Ποιες ειναι οι διαφορες τωρα της 6.47.10 με την 6.48.3 ?

Γιατι απ οσο καταλαβαινω έχουν περάσει τις αλλαγες στην long term.

BillyVan
05-06-21, 09:54
Νεο winbox


https://mt.lv/winbox64


What's new in v3.28:

*) added support for "contains" and "contains not" filtering in IPv4 address ranges;
*) allow to modify DHCPv6 server binding settings;
*) do not show newly created elements as invalid (in red);
*) expand table flag column to show all possible flags;
*) fixed IPv6 prefix column sorting in tables;
*) fixed WinBox crash after saving current session;
*) fixed WinBox crash when accessing v7 routes with VRF set;
*) fixed WinBox crash when some opened element was removed;
*) fixed WinBox disconnect when large text was pasted into terminal window;
*) fixed problem where optional field disappeared if window was maximized;
*) fixed table row selection with keyboard to match Windows behavior;
*) keep inner maximized window maximized when changing WinBox window size;
*) show missing Security Profile field in WiFi simple mode;

deniSun
05-06-21, 13:09
Νεο winbox


https://mt.lv/winbox64


What's new in v3.28:

*) added support for "contains" and "contains not" filtering in IPv4 address ranges;
*) allow to modify DHCPv6 server binding settings;
*) do not show newly created elements as invalid (in red);
*) expand table flag column to show all possible flags;
*) fixed IPv6 prefix column sorting in tables;
*) fixed WinBox crash after saving current session;
*) fixed WinBox crash when accessing v7 routes with VRF set;
*) fixed WinBox crash when some opened element was removed;
*) fixed WinBox disconnect when large text was pasted into terminal window;
*) fixed problem where optional field disappeared if window was maximized;
*) fixed table row selection with keyboard to match Windows behavior;
*) keep inner maximized window maximized when changing WinBox window size;
*) show missing Security Profile field in WiFi simple mode;

:oneup:

deniSun
05-07-21, 20:39
6.49beta54 changelog:
Changes in this release:


*) bridge - fixed external flag in the host table for wireless clients;
*) capsman - use Bits instead of Bytes for "ap-tx-limit" and "client-tx-limit" parameters;
*) crs3xx - fixed jumbo frame forwarding for CRS354 devices (introduced in v6.49beta36);
*) crs3xx - fixed unknown multicast flood to CPU when IGMP snooping is used;
*) crs3xx - improved system stability when increasing interface L2MTU for CRS318 devices;
*) defconf - apply default configuration from branding package when performing reset with button;
*) defconf - fixed default configuration loading on LHG R;
*) health - fixed voltage monitor on BaseBox5 devices;
*) ike2 - added "MS-CHAP-Domain" attribute to RADIUS requests;
*) ike2 - added support for ASN.1 DN "my-id" value setting for initiators;
*) ike2 - check if TS is still valid after obtaining SPI;
*) ipsec - improved SA update by SPI;
*) leds - fixed "/system leds" menu on RBLHG-2nD;
*) lora - added channel plan "il-917" for Israel;
*) lte - added support for Sharp 809SH;
*) m33g - improved support for "/system gpio" menu ("/system routerboard upgrade" required);
*) sfp - improved 25Gbps optical module stability and linking;
*) snmp - added "engine-id" OID support;
*) snmp - fixed "ipNetToMediaType" OID for incomplete entries;
*) ssh - fixed "undo" functionality;
*) system - improved stability when receiving bogus packets;
*) telnet - fixed "routing-table" parameter usage;
*) tr069-client - added support for Ethernet link speed reporting;
*) tr069-client - added support for interface comment reporting and editing;
*) tr069-client - added support for supout file upload;
*) tr069-client - improved stability for download/upload diagnostics;
*) ups - added battery info for APC Back-UPS BX750MI;
*) w60g - general stability and performance improvements;
*) webfig - added support for logo image from branding package;
*) winbox - added "Cloud Backup" options under "Files" menu;
*) winbox - added "interworking-profile" parameter under "Wireless" menu;
*) winbox - added "name" and "file-name" parameter when importing and exporting certificates;
*) winbox - added "sfp-shutdown-temperature" setting to SFP interfaces;
*) winbox - added SSH settings under "IP/SSH" menu;
*) winbox - added TFTP settings under "IP/TFTP/Settings" menu;
*) winbox - allow setting MCS (24-31) to 4x4 Wireless interfaces;
*) winbox - do not allow to set empty "init-string" field under "System/GPS" menu;
*) winbox - do not show "Functionality" field for LTE interface if it is not provided;
*) winbox - do not show "GPS antenna" selection for devices without selection support;
*) winbox - fixed "Secondary Frequency" parameter setting under "CAPsMAN/Channel" menu;
*) winbox - fixed "Switch" menu on RBwAPG;
*) winbox - fixed DNS "cache-size" parameter setting;
*) winbox - fixed order of weekdays under "IP/Firewall" menu;
*) winbox - match "MAC Protocol-Num" predefined values under "Bridge/Filters" menu;
*) winbox - properly show "CRL Signature" field under "System/Certificate" menu;
*) winbox - show "System/Health" only on boards that have health monitoring;
*) winbox - show IPv6 address in separate field under "IP/Cloud" menu;
*) wireless - added override for multicast-to-unicast translation of DHCP traffic;
*) wireless - added U-NII-2 support for US and Canada country profiles for hAP ac^3;

deniSun
23-08-21, 14:27
What's new in v3.29:

*) added "Windows" menu for list of all currently opened windows;
*) added separate "Show Columns" window for list of visible columns;
*) allow changing column order by using drag and drop;
*) made "Terminal" window titles unique;

x_undefined
23-08-21, 14:37
allow changing column order by using drag and drop;

ΕΠΙΤΕΛΟΥΣ!

deniSun
23-08-21, 17:49
What's new in 6.48.4 (2021-Aug-18 06:43):


*) branding - fixed missing branding skins if "skins" folder does not exist;
*) bridge - added MAC and IP source addresses information for DHCP snooping log;
*) bridge - fixed "vlan-encap" setting for filter and NAT rules;
*) bridge - improved system stability when using IGMP snooping and changing bridge MAC address;
*) capsman - use Bits instead of Bytes for "ap-tx-limit" and "client-tx-limit" parameters;
*) crs3xx - fixed unknown multicast flood to CPU when IGMP snooping is used;
*) crs3xx - improved system stability when increasing interface L2MTU for CRS318 devices;
*) defconf - fixed default configuration loading on LHG R;
*) defconf - fixed minor typo in configuration description;
*) dhcpv6-server - fixed false missing IPv6 Pool warning for dynamic bindings;
*) dns - fixed CNAME query when target record is not in cache;
*) dns - fixed cache memory leak when resolving CNAME domains;
*) health - fixed voltage monitor on BaseBox5 devices;
*) health - improved temperature reporting;
*) ike2 - added "MS-CHAP-Domain" attribute to RADIUS requests;
*) leds - fixed "/system leds" menu on RBLHG-2nD;
*) lora - added additional predefined network servers;
*) lte - added support for Sharp 809SH;
*) routerboard - fixed "reset-button" on hAP ac;
*) system - improved stability when receiving bogus packets;
*) telnet - fixed "routing-table" parameter usage;
*) w60g - improved stability in low temperature environments;
*) webfig - do not show "units" twice in multi list entries;
*) winbox - added "Cloud Backup" options under "Files" menu;
*) winbox - added "interworking-profile" parameter under "Wireless" menu;
*) winbox - added support for PTP;
*) winbox - do not show "Functionality" field for LTE interface if it is not provided;
*) winbox - fixed "Switch" menu on RBwAPG;
*) winbox - fixed "vid" parameter under "Bridge/Hosts" menu;
*) winbox - show "System/Health" only on boards that have health monitoring;
*) wireless - added U-NII-2 support for US and Canada country profiles for hAP ac^3;
*) wireless - added U-NII-2 support for US and Canada country profiles for hap ac, hAP ac^3 LTE6, Audience and Audience LTE6;
*) wireless - updated "israel" regulatory domain information;

jkarabas
26-08-21, 14:15
Έβαλα τη νέα έκδοση stable και έχασα όλα τα scripts.

- - - Updated - - -

Κάπου κόλλησε και τελικά μετά από reboot επανήλθε.

deniSun
26-08-21, 18:00
Έβαλα τη νέα έκδοση stable και έχασα όλα τα scripts.

- - - Updated - - -

Κάπου κόλλησε και τελικά μετά από reboot επανήλθε.

Έκανες upd το firmware;
Κατέβασες το νέο Winbox;

jkarabas
26-08-21, 18:48
Έκανες upd το firmware;
Κατέβασες το νέο Winbox;

Όλα εντάξει!!

x_undefined
06-09-21, 17:34
Από σήμερα σταμάτησε να δουλεύει πρακτικά το IP Cloud επειδή για κάποιο λόγο έγινε suspended το domain που χρησιμοποιεί (mynetname.net)

https://forum.mikrotik.com/viewtopic.php?f=2&t=178262

Το ποστάρω εδώ σε περίπτωση που ψάχνεται και κάποιος άλλος γιατί δεν δουλεύει.

Nikiforos
06-09-21, 18:36
Από σήμερα σταμάτησε να δουλεύει πρακτικά το IP Cloud επειδή για κάποιο λόγο έγινε suspended το domain που χρησιμοποιεί (mynetname.net)

https://forum.mikrotik.com/viewtopic.php?f=2&t=178262

Το ποστάρω εδώ σε περίπτωση που ψάχνεται και κάποιος άλλος γιατί δεν δουλεύει.

καλησπερα, καλα εισαι και ο πρωτος, εκανα ρυθμισεις στο DVR CCTV του εξοχικου και για ποιο γρηγορα μπηκα απευθειας αντι με openvpn και ειχα θεμα, ειχα ομως και noip, ενω αυτο επαιξε με το mikrotik ip cloud μπα!
και ψαχνομουνα τι εγινε!!!
και τωρα τι θα γινει? θα κανουν κατι?

x_undefined
07-09-21, 18:58
Απ' ό,τι φαίνεται δουλεύει και πάλι κανονικά.

RpMz
07-09-21, 23:47
Ναι έφτιαξε.

alefgr
08-09-21, 00:09
Παρατηρώ στην τελευταία version του winbox, ότι όταν καλώ να κάνει μια σύνδεση σε ένα router και μάλιστα από το τοπικό δίκτυο, κάνει αρκετά δευτερόλεπτα μέχρι να ενημερώσει όλα τα παράθυρα που έχω ανοικτά. Μέχρι την προηγούμενη version τα σχημάτιζε σχεδόν ακαριαία. Το έχει παρατηρήσει και κανείς άλλος αυτό το σύμπτωμα, ή το κάνει μόνο σε εμένα;

x_undefined
08-09-21, 00:16
Σε εμένα δεν έχει αλλάξει κάτι, αλλά έχω μόνο 3 παράθυρα συνήθως ανοικτά.

deniSun
16-09-21, 12:33
WinBox v3.31 released!

What's new in v3.31:

*) ask to close all WinBox instances before WinBox upgrade, otherwise upgrade will fail;
*) fixed table to properly show and hide columns and remember its widths;
*) made MAC-telnet work if SSH or telnet was used before;
*) update file path after changing its location with drag&drop;

macro
17-09-21, 10:49
Επιτελους φτιαξανε τα columns............

jkarabas
18-09-21, 07:28
Επιτελους φτιαξανε τα columns............

:oneup:

alefgr
20-09-21, 03:16
Εγώ πάντως συνεχίζω να έχω το ίδιο πρόβλημα με τις τρις τελευταίες εκδόσεις. Όταν το τρέχω μου αργεί πολύ να ενημερώσει τα παράθυρα. Για να ενημερώσει τα 6 παράθυρα που έχω πάντα ανοικτά, πρέπει να περιμένω 12 με 15 δευτερόλεπτα, ενώ στις παλιές εκδώσεις ήταν σχεδόν ακαριαία η ενημέρωση.

Nikiforos
20-09-21, 06:49
καλημερα, λειτουργικο?
εγω σε win 10 και Linux μεσω wine ολα ακαριαια κανενα προβλημα απολυτως σε καμια απο αυτες τις εκδοσεις, 3.31, 3.30 και τις προηγουμενες.
Μηπως φταιει κατι αλλο ? μηπως κατι με τα συγκεκριμενα παραθυρα που εχεις ανοιχτα?

alefgr
21-09-21, 06:51
Η αλήθεια είναι πως είμαι σε παλιό λειτουργικό, στα win 2003. Όσο για τα παράθυρα, σίγουρα δεν φταίνε. Με την 3.27 version που δοκίμασα, συνεχίζουν να ανοίγουν ακαριαία.

Nikiforos
21-09-21, 17:50
Η αλήθεια είναι πως είμαι σε παλιό λειτουργικό, στα win 2003. Όσο για τα παράθυρα, σίγουρα δεν φταίνε. Με την 3.27 version που δοκίμασα, συνεχίζουν να ανοίγουν ακαριαία.

Εχεις δοκιμασει αλλο λειτουργικο ?

alefgr
22-09-21, 03:42
Στα win 2019 που δοκίμασα σήμερα την 64 bit τελευταία version, δεν το παρουσιάζει. Οπότε το συμπέρασμα είναι ότι το winbox αρχίζει σιγά-σιγά να έχει ασυμβατότητα με τα xp, και πρέπει να σταματήσω τις αναβαθμίσεις του.

Επίσης παιδεύτηκα να μεταφέρω όλες τις ρυθμίσεις του winbox στο άλλο μηχάνημα. Δεν υπάρχει τρόπος να κάνουμε γενικό αντίγραφο; Πίστευα πως αν έχουν απλώς κοινό δικτυακό folder με όλα τα sessions, θα υπήρχαν μαζί και οι διευθύνσεις μαζί με τα logins. Όσο για το export και το import δυστυχώς δεν αντιστοιχίζει την κάθε διεύθυνση στο συγκεκριμένο session και πρέπει να γίνει manual η αλλαγή και η αποθήκευση.

deniSun
07-10-21, 22:03
What's new in 6.49 (2021-Oct-06 11:55):



*) branding - fixed LCD logo loading from branding package when installed via Netinstall;
*) branding - properly clean up old branding files before installing a new one;
*) bridge - added IGMP and MLD querier monitoring;
*) bridge - added IGMP snooping log when multicast table gets full;
*) bridge - fixed external flag in the host table for wireless clients;
*) bridge - improved controller bridge stability when adding RouterOS v7 port extender;
*) bridge - improved port extender stability when creating bond interfaces on excluded ports;
*) bridge - improved stability when quickly adding and removing bridge interface;
*) certificate - improved stability when removing dynamic CRL entries;
*) chr - fixed OS provisioning on Azure;
*) chr - improved stability when changing "flow-control" settings on interfaces with e1000 drivers;
*) conntrack - increased total connection tracking table size based on installed RAM size;
*) console - require "write+ftp" permissions for executing script to file;
*) console - require "write+ftp" permissions for printing to file;
*) crs3xx - correctly filter packets by L2MTU on 1Gbps Ethernet interfaces for CRS354 devices;
*) crs3xx - fixed LEDs for QSFP+ interface on CRS326-24S+2Q+ device;
*) crs3xx - fixed SFP and SFP+ link rate reporting (introduced in v6.48beta11);
*) crs3xx - fixed bridge controller and extender packet forwarding for CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - fixed default MAC address calculation on management Ethernet for CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - fixed interface flow control;
*) crs3xx - improved QSFP+ linking and mode changing for CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - improved packet transmit on SFP+ interfaces;
*) crs3xx - improved switch resource allocation for CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) defconf - apply default configuration from branding package when performing reset with button;
*) defconf - removed overlapping IPv6 firewall rules;
*) defconf - use router as DNS server for DHCP hosts;
*) dhcp-server - fixed DHCP Option decimal value parsing;
*) dhcpv4-server - reset dynamic "bcast" flag when receiving offer from DHCP relay;
*) dhcpv4-server - reset lease's dynamic "bcast" flag on packets from relay;
*) dhcpv6-server - check if pool name has changed from RADIUS on renew;
*) dhcpv6-server - improved dynamic server entry update;
*) discovery - do not send discovery packets on interfaces that are blocked by STP (introduced in v6.48);
*) dns - fixed memory leak caused by large DNS replies;
*) firewall - fixed "ingress-priority" matcher;
*) firewall - fixed GRE protocol packets considered invalid when PPTP helper is disabled;
*) gps - improved interface monitoring;
*) health - added "phy-temperature" sensor monitoring for CRS312 device;
*) health - improved temperature readings on hEX S;
*) health - improved temperature reporting;
*) ike2 - added support for ASN.1 DN "my-id" value setting for initiators;
*) ike2 - check if TS is still valid after obtaining SPI;
*) ike2 - fixed initiator packet retransmit with DDOS cookie;
*) ipsec - fixed memory leak when processing DHCP packets;
*) ipsec - improved SA update by SPI;
*) ipsec - improved system stability on CHR;
*) ipsec - improved system stability on MMIPS devices;
*) kid-control - improved IPv6 firewall rule generation;
*) led - added LTE LED support for LHGGR;
*) leds - fixed LTE LED default mapping for wAP R ac LTE kit;
*) lora - added additional predefined network servers;
*) lora - added channel plan "il-917" for Israel;
*) lora - fixed "PULL_DATA" token generation;
*) m33g - improved support for "/system gpio" menu ("/system routerboard upgrade" required);
*) m33g - removed 12..16 pins from "/system gpio" menu;
*) mipsbe - improved booting speed on non-NAND devices ("/system routerboard upgrade" required);
*) mpls - allow to disable FastPath (CLI only);
*) mqtt - added server name indication;
*) netinstall - fixed lock file persistence after reinstall;
*) netinstall - improved bootp packet handling on Linux netinstall-cli version when multiple NIC's are present;
*) netinstall - require Netinstall version to be the same or newer as "factory-software";
*) ntp - use correct IPv6 multicast group for SNTP client;
*) package - always allow to uninstall package even if there is no free disk space left;
*) poe - update PoE firmware only on devices that supports it;
*) ppp - improved stability when receiving bogus response on modem channel;
*) qsfp - improved system stability when setting unsupported link rates;
*) quickset - use 5GHz interface's country for "Home AP Dual" configuration;
*) routerboard - fixed "reformat-hold-button-max" validation for values below 10s;
*) sfp - added "sfp-rate-select" setting;
*) sfp - fixed GPON module linking (introduced in v6.47);
*) sfp - improved 25Gbps optical module stability and linking;
*) sfp - improved SFP, SFP+, SFP28 and QSFP+ interface stability for CRS3xx and CCR2004 devices;
*) sfp - improved link stability for 10G, 25G and 40G modules on CRS309, CRS312, CRS326-24S+2Q+ CRS354 and CCR2004 devices;
*) sfp28 - changed FEC auto mode to disabled;
*) snmp - added "engine-id" OID support;
*) snmp - fixed "ipNetToMediaType" OID for incomplete entries;
*) ssh - fixed "undo" functionality;
*) supout - added controller bridge section;
*) supout - print detailed list of active user sessions;
*) switch - fixed (R/M)STP port blocking right before switching them in HW bridge (fixes possible packet loop when changing bridge settings);
*) switch - improved packet transmit between CPU and 98PX1012 for CCR2004-1G-12S+2XS device;
*) swos - fixed "static-ip-address" parameter;
*) tr069-client - added "X_MIKROTIK_LinkDowns" parameter for interface "link-downs" value reporting;
*) tr069-client - added support for Ethernet link speed reporting;
*) tr069-client - added support for interface comment reporting and editing;
*) tr069-client - added support for supout file upload;
*) tr069-client - fixed traceroute diagnostics time values;
*) tr069-client - improved XML with new-lines for readable output;
*) tr069-client - improved stability for download/upload diagnostics;
*) upgrade - fixed free space checking on flash type memories when installing new packages;
*) ups - added battery info for APC Back-UPS BX750MI;
*) user - added "expired" user status with suggestion to change password (WinBox v3.29 required);
*) user - fixed active user session purging on disconnect;
*) user - show "expired password" prompt for users with blank password;
*) w60g - general stability and performance improvements;
*) w60g - limit power output when using region EU to match EN302567 on nRAY;
*) w60g - use EU region by default;
*) webfig - added support for logo image from branding package;
*) webfig - do not show value units twice;
*) webfig - fixed "Wireless/CAP" menu opening;
*) webfig - fixed interface sorting by name;
*) webfig - show only "Close" button under "Wireless/Wireless Sniffer/Sniffed Packets" menu;
*) winbox - added "dhcp" option to "multicast-helper" setting;
*) winbox - added "fec-mode" parameter under "Interface/Ethernet" menu;
*) winbox - added "interface-speed-100G" LED type to "System/LEDs" menu;
*) winbox - added "name" and "file-name" parameter when importing and exporting certificates;
*) winbox - added "sfp-shutdown-temperature" setting to SFP interfaces;
*) winbox - added SSH settings under "IP/SSH" menu;
*) winbox - added TFTP settings under "IP/TFTP/Settings" menu;
*) winbox - allow setting MCS (24-31) to 4x4 Wireless interfaces;
*) winbox - do not allow to add/remove W60G interfaces;
*) winbox - do not allow to set empty "init-string" field under "System/GPS" menu;
*) winbox - do not show "GPS antenna" selection for devices without selection support;
*) winbox - fixed "Secondary Frequency" parameter setting under "CAPsMAN/Channel" menu;
*) winbox - fixed DNS "cache-size" parameter setting;
*) winbox - fixed health reporting on RB960, hEX, hEX S and hAP ac3 devices;
*) winbox - fixed order of weekdays under "IP/Firewall" menu;
*) winbox - fixed support for "Delegated-IPv6-Prefix" for PPP services;
*) winbox - match "MAC Protocol-Num" predefined values under "Bridge/Filters" menu;
*) winbox - minimal required version is v3.30;
*) winbox - properly show "CRL Signature" field under "System/Certificate" menu;
*) winbox - separated CCQ Tx and Rx values in their own unique columns;
*) winbox - show "System/Health/Settings" only on boards that have configurable values;
*) winbox - show "current-channel" column by default for CAP interfaces;
*) winbox - show IPv6 address in separate field under "IP/Cloud" menu;
*) wireless - added U-NII-2 support for US and Canada country profiles for hAP ac lite;
*) wireless - added override for multicast-to-unicast translation of DHCP traffic;
*) wireless - do not remove channels >2462 MHz from "scanlist" if scanning for fixed channel;
*) wireless - do not send packet back to station-bridge it was received from;
*) wireless - fixed minor typo in debug logging messages;
*) wireless - improve WMM priority assignment for packets with internal priority greater than 7;
*) wireless - improve regulatory compliance with DFS requirements;
*) wireless - improve signaling of QCA9984 interface capabilities when using 160/80+80MHz channel width;
*) wireless - improved system stability when sending packets through interface after L2MTU is increased;
*) wireless - log client signal strength on disconnect;
*) wireless - renamed "secondary-channel" to "secondary-frequency";
*) wireless - updated "israel" regulatory domain information;
*) wireless - updated "united kingdom" regulatory domain information;

Τ Ε Ρ Α Σ Τ Ι Ο

BillyVan
07-10-21, 23:27
χαχα να δουλευει μονο καλα κι ας αργησει η 6.49.1 ....

deniSun
08-10-21, 10:46
χαχα να δουλευει μονο καλα κι ας αργησει η 6.49.1 ....

Έτσι που πάμε με τις 6.Χ, την 7 την βλέπω σε καμιά 10αριά χρόνια.

BillyVan
08-10-21, 11:30
Δεν με ενοχλει καθολου να μεινω στην 6.χχ αρκει να τη φτιαξουνε.

Διαβαζω κωμικοτραγικα για την 6.49 στο φορουμ τους.

Κατα το γνωστο εφτιαξαν 10 χαλασαν 2-3.

Δεν ασχολουμαι πια με την 7.

Το μονο καλο ειναι το wireguard που παιζει καλα.

Εχει αλλαξει ολος ο τροπος του ρουτινγκ στην 7 κατι που με δυσκολευει και δε θελω να ανακαλυψω τον τροχο.

Οι οδηγιες στο wiki ειναι ελαχιστες και δεν υπαρχει ακομη γνωση περι 7 ρος οποτε.....στο μελλον βλεπουμε.

deniSun
08-10-21, 11:44
Δεν με ενοχλει καθολου να μεινω στην 6.χχ αρκει να τη φτιαξουνε.

Διαβαζω κωμικοτραγικα για την 6.49 στο φορουμ τους.

Κατα το γνωστο εφτιαξαν 10 χαλασαν 2-3.

Δεν ασχολουμαι πια με την 7.

Το μονο καλο ειναι το wireguard που παιζει καλα.

Εχει αλλαξει ολος ο τροπος του ρουτινγκ στην 7 κατι που με δυσκολευει και δε θελω να ανακαλυψω τον τροχο.

Οι οδηγιες στο wiki ειναι ελαχιστες και δεν υπαρχει ακομη γνωση περι 7 ρος οποτε.....στο μελλον βλεπουμε.

Συγκεκριμένα ένα που διάβασα για το 4011 που έχω και εγώ... σε εμένα δεν συμβαίνει.
Σε όλες τις αναβαθμίσεις υπάρχουν προβλήματα.
Διαφορετικά με καμιά 100αριά θα είχα φτάσει στην τελειότητα.

jkarabas
08-10-21, 12:59
Εγώ πάντως το τόλμησα το update.

- - - Updated - - -


Το μονο καλο ειναι το wireguard που παιζει καλα.

Καλό νέο αυτό.

deniSun
08-10-21, 14:26
Changes since 6.48.4: Long-term]

*) branding - properly clean up old branding files before installing a new one;
*) crs3xx - fixed default MAC address calculation on management Ethernet for CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) gps - improved interface monitoring;
*) health - improved temperature reporting;
*) ike2 - check if TS is still valid after obtaining SPI;
*) ipsec - improved SA update by SPI;
*) netinstall - require Netinstall version to be the same or newer as "factory-software";
*) poe - update PoE firmware only on devices that supports it;
*) ppp - improved stability when receiving bogus response on modem channel;
*) qsfp - improved system stability when setting unsupported link rates;
*) sfp - added "sfp-rate-select" setting (CLI only);
*) sfp - improved SFP, SFP+, SFP28 and QSFP+ interface stability for CRS3xx and CCR2004 devices;
*) sfp28 - changed FEC auto mode to disabled;
*) w60g - limit power output when using region EU to match EN302567 on nRAY;
*) w60g - use EU region by default;
*) winbox - added "name" and "file-name" parameter when importing and exporting certificates;
*) winbox - allow setting MCS (24-31) to 4x4 Wireless interfaces;
*) winbox - do not allow to set empty "init-string" field under "System/GPS" menu;
*) winbox - do not show "GPS antenna" selection for devices without selection support;
*) winbox - show "System/Health/Settings" only on boards that have configurable values;
*) winbox - show "current-channel" column by default for CAP interfaces;
*) wireless - added U-NII-2 support for US and Canada country profiles for hAP ac lite;

BillyVan
08-10-21, 20:13
6.48.5

deniSun
17-11-21, 17:09
What's new in 6.49.1 (2021-Nov-17 10:06):


MAJOR CHANGES IN v6.49.1:
----------------------
!) device-mode - added feature locking mechanism;
----------------------

Changes in this release:

*) certificate - improved stability when sending bogus SCEP message;
*) conntrack - limit total connection tracking table size based on installed RAM size;
*) crs3xx - fixed interface linking for some optical QSFP+ modules on CRS354 devices;
*) dhcpv6-server - fixed DUID generation with timestamp;
*) health - improved temperature reporting;
*) led - added "dark-mode" functionality control with Mode button for cAP XL ac;
*) leds - fixed LTE LED default mapping for LHGG;
*) lte - improved RSSI reporting on R11e-LTE6;
*) routerboot - enabling "protected-routerboot" feature requires a press of a button;
*) snmp - fixed IPsec-SA byte and packet counter reporting;
*) sstp - fixed client stuck in "nonce matching" state;
*) system - improved system stability if device is upgraded from RouterOS and/or RouterBOOT v6.41.4 or older;
*) traffic-flow - added systematic count-based packet sampling support;
*) upgrade - added new "upgrade" channel for upgrades between major versions;
*) winbox - added "Modbus" menu support;
*) wireless - added U-NII-2 support for US and Canada country profiles for cAP ac XL and QRT 5 ac;
*) wireless - fixed frequency range information on IPQ4019;

jkarabas
18-11-21, 21:20
Μετά το update έγινε disable το wireless package στο hap-ac2 και δεν μπορώ να το επαναφέρω.

deniSun
18-11-21, 23:06
Μετά το update έγινε disable το wireless package στο hap-ac2 και δεν μπορώ να το επαναφέρω.

reset, netinstall και περνάς το τελευταίο backup.

jkarabas
19-11-21, 07:53
reset, netinstall και περνάς το τελευταίο backup.

Καλημέρα
Το επανέφερα τελικά χωρίς netinstall.

Nikiforos
19-11-21, 17:36
Καλημέρα
Το επανέφερα τελικά χωρίς netinstall.

καλησπερα, τι εφταιγε τελικα και πως το εφτιαξες για την ιστορια? εμενα δεν εγινε κατι ευτυχως.

jkarabas
19-11-21, 18:37
καλησπερα, τι εφταιγε τελικα και πως το εφτιαξες για την ιστορια? εμενα δεν εγινε κατι ευτυχως.

Έκανα enable μέσα απο τα πακέτα 2 φορές το wireless με reboot αλλά δεν επανήλθε.
Μετά κατέβασα το πακέτο ξεχωριστά το έκανα install με επανεκινηση - enable ξανά και επανήλθε.

BillyVan
19-11-21, 20:11
Έκανα enable μέσα απο τα πακέτα 2 φορές το wireless με reboot αλλά δεν επανήλθε.
Μετά κατέβασα το πακέτο ξεχωριστά το έκανα install με επανεκινηση - enable ξανά και επανήλθε.

Ενω ειχες κανει αναβαθμισει το βασικο routeros-arm-6.49.1.npk το επαθε?

Και μετα εκανες install μονο το πακετο wireless απ το Extra packages?

Περιεργο...

Θα το σκεφτω στην 6.49.5 6 7 αν θα παω...:)

καλα κανω κι εχω μεινει στην 6.84.4 ακομη εγω σε όλα

@ ADSLgr.com All rights reserved.