Downloads: Pap 2T v.5.1.6

Pap 2T v.5.1.6

Rate this File
Uploaded by nnn - 09-11-06
Author Author Linksys
File Size File Size 1,43 MB
Downloads Downloads 79
+ Download
Νέο firmware για το Internet Phone Adapter with 2 Ports for Voice-over-IP PAP 2T v.5.1.6
Release Notes for -- Linksys PAP2/PAP2T 5.1.6

PAP2 -- 2 Port FXS, 1 Ethernet Interface
PAP2T -- 2 Port FXS, 1 Ethernet Interface

Copyright (C) 2007 by Linksys, a Division of Cisco Systems, Inc.

All Rights Reserved.

* * * * * * * * * * IMPORTANT * * * * * * * * * * * * * * * * *
* Use of Proprietary Information and Copyright Notice: *
* This release note document contains proprietary information *
* that is to be used only by Sipura Technology, Linksys(R), *
* and Cisco Systems, Inc. customers. Any unauthorized *
* disclosure, copying, distribution, or use of this *
* information is prohibited. This restriction includes *
* ALL Internet based discussion forums, e.g. DSLreports. *
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

/** NOTICE **/
official release

========================================
New Features
========================================

--- External Notes ---

- If REGISTER results in a 301 response with a Contact header
that has a maddr URI parameter, and if the <Outbound Proxy>
is an IP address, the SPA will change the outproxy proxy
address to the value of the maddr address. This value will
remain valid until the next 301 response, if any, or will
restore to the originally configured value upon reboot.

- When swapping calls in a call-waiting or similar situation,
the SPA will order the operations to make sure that call hold
is invoked before call resume.

- New RC blink pattern. Power LED red-orange slow blink while
contacting server. Red-orange double blink if file not found
or corrupt.

- 1. Make DHCP DISCOVER retry longer (120 Seconds)2. Reboot the
device in 10 minutes if the device is using last konwn good
IP address.

========================================
Bug Fixes
========================================

--- External Notes ---

- SDP in INVITE response, includes annexb=yes/no if present in
INVITE message

- Fixed this problem: A,B,C,D digits are dropped when dialing

- SPA should escape occurrences of '#' in the dial string with
%23 in outbound INVITE

- Fixed this problem: Unit stops playing incoming RTP audio once
it receives a 180/183 w/o SDP; regardless setting of <Sticky 183>
parameter

- bug fix: Bogus IP may be used if dns srv failed when querying
the proxy server.

- Worked around this problem: some server will change the Contact
header's address in their response to the SPA's SIP REGISTER
request, so that the SPA cannot find the corresponding Contact
in the response and therefore may not be able to extract the
proper expires value inserted by the server. This is a problem
if the expires value inserted by the server in the response is
smaller than the value in the original SIP REGISTER request.
The work around is to use the first entry in the Contact header
if an exactly matching address is not found.

- Fixed this problem: If unknown response is received, such as 101,
SPA might misinterpret it as a 6xx response. In some other cases,
an unknown response, such as 188, might be dropped by the SPA as
a bad message. The proper way is to treat it as the corresponding
base response, such as 100.

- Fixed this problem: Daylight Saving Time is not correct if start
time is later then end time of the year in the <Daylight Saving
Time Rule> parameter

- Fixed this problem: Unit should ignore in-dialog re-INVITE if it
has not received ACK to the 200 response to the initial INVITE
from the caller. This condition might happen if the ACK was lost
but the first re-INVITE has already been sent by the peer.

- Fixed this problem: Unit should not filter out leading * or #
digit in the incoming caller id number, as these can be legitimate
phone number digits

- Fixed this problem: PAP2T cannot detect DTMF digits at 50ms on/off
during a call, even if <DTMF Tx Mode> is "normal".

- Fixed missing '*' and '#' in on-hook caller-id number generation

- Eliminated cause of spurious reboot on resync for customized units
with read-only parameters and value mismatch.

Images

  • Pap 2T v.5.1.6

Comments

There are no comments yet.