Mikrotik ROS RC version συζητήσεις-bugs κτλ.

**deniSun** · 24-04-20, 17:19

6.47beta60 changelog:
Important note!!!

- The Dude server must be updated to monitor v6.46.4 and v6.47beta30+ RouterOS type devices.
- The Dude client must be manually upgraded after upgrading The Dude server.
- Make sure LTE APN Profile name does not match any of the DHCP server's names if LTE passthrough is used.
- The Dude requires "winbox" policy instead of "dude" to monitor v6.46.4 and v6.47beta30+ RouterOS type devices.

MAJOR CHANGES IN v6.47:
----------------------
!) dns - added client side support for DNS over HTTPS (DoH) (RFC8484);
!) socks - added support for SOCKS5 (RFC 1928);
!) user - enable "winbox" policy for groups with "dude" policy;
----------------------

Changes in this release:

Spoiler:

!) dns - added client side support for DNS over HTTPS (DoH) (RFC8484);
!) socks - added support for SOCKS5 (RFC 1928);
*) branding - improved branding package installation process when another branding package is already installed;
*) chr - enabled support for VMBus protocol version 4.1;
*) chr - improved system stability when running CHR on Hyper-V;
*) crs3xx - fixed hardware offloaded bonding on Ethernet interfaces for CRS354 devices;
*) crs3xx - fixed switch rule "dst-port" parameter for IPv6 traffic on CRS305-1G-4S+, CRS326-24G-2S+, CRS328-24P-4S+, CRS328-4C-20S-4S+, netPower 15FR devices;
*) crs3xx - improved system stability when creating multiple hardware offloaded bonding interfaces (introduced in v6.47beta49);
*) crs3xx - show correct switch model for netPower 15FR device;
*) defconf - fixed default IP address assigning on non-paired 60 GHz devices;
*) disk - improved disk management service stability when receiving bogus packets;
*) dns - added support for forwarding DNS queries of static entries to specific server (CLI only);
*) dns - added support for multiple type static entries (CLI only);
*) email - added support for multiple "to" recipients (CLI only);
*) graphing - improved graphing service stability when receiving bogus packets;
*) ike1 - do not try to keep phase 2 when purging phase 1;
*) ike2 - added support for RADIUS Disconnect-Request message handling;
*) interface - increased loopback interface MTU to 65536;
*) ipsec - allow specifying two peers for a single policy for failover (CLI only);
*) lora - added "altitude", "latitude" and "longitude" to stat json if GPS is available;
*) lte - improved stability during firmware upgrade process;
*) routerboard - added "hold-time" parameter to mode-button menu (CLI only);
*) routerboard - added "reset-button" menu - custom command execution with reset button (CLI only);
*) snmp - fixed "ifSpeed" reporting for tunnel interfaces;
*) ssh - improved SSH service stability when receiving bogus packets;
*) switch - correctly display switch statistics when all switch ports are disabled on RTL8367 switch chip;
*) switch - fixed missing switch statistics (introduced in v6.47beta49);
*) user - improved user management service stability when receiving bogus packets;
*) webfig - fixed WinBox download link;
*) webfig - fixed skin usage from branding package;
*) winbox - added "bus" parameter for "USB Power Reset" command on RBM33G;
*) winbox - allow to specify any ethernet like interface under "Tool/WoL" menu;
*) winbox - fixed "Tx/Rx Signal Strength" value presence for 4 chain interfaces;
*) winbox - fixed memory leak (introduced in v6.46.4);
*) winbox - fixed wireless interface "HT" tab setting presence when "band=5ghz-n/ac";
*) winbox - increased limit of multi-entry fields to 100;
*) winbox - limit number of simultaneous WinBox sessions to 5 for users without "write" permission;
*) wireless - improved management service stability when receiving bogus packets;
*) wireless - updated "south africa" regulatory domain information;

**deniSun** · 26-05-20, 11:31

6.47rc2 changelog:
Important note!!!

- The Dude server must be updated to monitor v6.46.4 and v6.47beta30+ RouterOS type devices.
- The Dude client must be manually upgraded after upgrading The Dude server.
- Make sure LTE APN Profile name does not match any of the DHCP server's names if LTE passthrough is used.
- The Dude requires "winbox" policy instead of "dude" to monitor v6.46.4 and v6.47beta30+ RouterOS type devices.

Changes in this release:

Spoiler:

**BillyVan** · 21-08-20, 14:28

6.48beta27 (2020-Aug-18

Αρκετό πράμα...

Spoiler:

**deniSun** · 21-08-20, 14:51

*) discovery - use "static" interface list by default instead of "!dynamic";

στην 6.47.2 την περασαν ως!dynamic

**Nikiforos** · 03-09-20, 16:44

What's new in 6.48beta35 (2020-Sep-02 07:50):

Κώδικας:

*) bonding - removed "sys-id" and "sys-priority" from monitor-slaves command;
*) bridge - fixed BPDU guard port disable/enable on HW offloaded interfaces;
*) bridge - fixed host table update on SNMP query;
*) bridge - fixed multicast table printing;
*) bridge - fixed packet forwarding for CAP and BCP controlled interfaces (introduced in v6.48beta12);
*) bridge - fixed STP alternate and backup port states for devices with switch chip (introduced in v6.47);
*) bridge - increased multicast table size to 4K entries;
*) crs3xx - fixed "mirror-source" property on switch port disable for CRS305, CRS326-24G-2S+, CRS328, CRS318 devices;
*) crs3xx - fixed port isolation for "switch-cpu" port for CRS305, CRS326-24G-2S+, CRS328, CRS318 devices;
*) crs3xx - fixed port isolation removal for "switch-cpu" port on CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - fixed "storm-rate" traffic limiting for switch-cpu port on CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - fixed switch ACL rules for CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - fixed switch port "egress-rate" removal for CRS305, CRS326-24G-2S+, CRS328, CRS318 devices;
*) crs3xx - fixed VLAN tagged packet forwarding on "switch-cpu" port for CRS305, CRS326-24G-2S+, CRS328, CRS318 devices (introduced in v6.48beta12);
*) defconf - improved CAP interface bridging;
*) defconf - improved default configuration generation on devices without wireless package installed;
*) discovery - added "lldp-med-net-policy-vlan" property for assigning VLAN ID (CLI only);
*) discovery - allow choosing which discovery protocol is used (CLI only);
*) discovery - fixed discovery on mesh ports;
*) discovery - fixed discovery packet sending on newly bridged port with "protocol-mode=none";
*) discovery - fixed discovery when enabled only on master port;
*) discovery - use interface MAC address when sending MNDP from slave port;
*) dns - added IPv6 support for DoH;
*) dns - fixed multiple TXT string replies;
*) dns - hide default static entry "type" from export;
*) fetch - fixed "src-address" usage for SFTP;
*) filesystem - improved long-term filesystem stability and data integrity;
*) health - removed unused "heater-control" and "heater-threshold" parameters;
*) hotspot - added support for captive portal advertising using DHCP (RFC7710);
*) hotspot - improved management service stability when receiving bogus packets;
*) ike2 - fixed local side NAT detection;
*) ipsec - do not kill connection when peer's "name" or "comment" is changed;
*) ipsec - refresh peer's DNS only when phase 1 is down;
*) lte - added support for Alcatel IK41VE1;
*) snmp - fixed value types for "dot1dStp";
*) tr069-client - send correct "ConnectionRequestURL" when using IPv6;
*) traffic-flow - added "sys-init-time" parameter support;
*) wireless - allow setting "tx-power" up to 40;

**Nikiforos** · 15-09-20, 20:30

What's new in 6.48beta40 (2020-Sep-14 13:34):

*) arm64 - improved reboot reason reporting in log;
*) bridge - added minor fixes and improvements for IGMP snooping with HW offloading;
*) bridge - fixed link-local multicast forwarding when IGMP snooping and HW offloading is enabled;
*) bridge - fixed MDB entry removal when using bridge port "fast-leave" property;
*) conntrack - automatically reduce connection tracking timeouts when table is full;
*) console - allow "once" parameter for bonding monitoring;
*) crs3xx - added initial Bridge Port Extender support (CLI only);
*) crs3xx - added initial Controlling Bridge support for CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices (CLI only);
*) crs3xx - added switch-cpu port VLAN filtering (switch-cpu port is now mapped with bridge interface VLAN membership when vlan-filtering is enabled);
*) crs3xx - fixed IGMP snooping for CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - fixed switch "copy-to-cpu" property for CRS305, CRS318, CRS326-24G-2S+, CRS328 devices;
*) detnet - fixed malformed dummy DHCP User Class option;
*) detnet - use MAC address from bridge interface instead of slave port;
*) dhcpv4-server - improved "client-id" value parsing;
*) ipsec - refresh peer's DNS only when phase 1 is down;
*) leds - fixed LED type setting;
*) smb - fixed possible memory leak;
*) sms - fixed SMS sending when both "interface" and "smsc" parameters are specified;
*) snmp - added information from IPsec "active-peers" menu to MIKROTIK-MIB;
*) snmp - fixed "/tool snmp-get" functionality (introduced in v 6.46beta43);
*) snmp - fixed value types for "dot1qPvid";
*) supout - added bonding interface monitor information;
*) switch - fixed Ethernet padding for small packets;
*) tr069-client - allow passing LTE firmware update URL as XML;
*) user-manager - do not allow creating limitation that crosses midnight;
*) user-manager - updated PayPal's root certificate authorities;
*) wireless - improved WPS process stability;

**deniSun** · 15-12-20, 14:20

6.48rc1 changelog:
Changes in this release:

Spoiler:

*) arm - improved system stability;
*) bgp - fixed VPNV4 RD byte order;
*) bonding - added LACP monitoring;
*) branding - fixed LCD logo loading from new style branding package;
*) bridge - added "multicast-router" monitoring value for bridge interface (CLI only);
*) bridge - added fixes and improvements for IGMP and MLD snooping;
*) bridge - fixed "multicast-router" setting on bridge enable;
*) capsman - fixed authentication when using CAPsMAN forwarding (introduced in v6.48beta48);
*) certificate - properly flush expired SCEP OTP entries;
*) chr - fixed VLAN tagged packet transmit on bridge for Hyper-V installations;
*) crs3xx - added initial Bridge Port Extender support;
*) crs3xx - fixed "switch-cpu" VLAN membership on bridge disable;
*) crs3xx - fixed "tag-stacking" for CRS305, CRS318, CRS326-24G-2S+ and CRS328 devices (introduced in v6.48beta58);
*) crs3xx - fixed bridge "port-extender" for CRS318 devices;
*) crs3xx - fixed ingress rate policer for CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices (introduced in v6.48beta35);
*) discovery - added "lldp-med-net-policy-vlan" property for assigning VLAN ID;
*) ethernet - fixed IP connectivity on SFP/SFP+ interfaces for CCR2004-1G-12S+2XS device (introduced in v6.48beta58);
*) ike1 - fixed 'rsa-signature-hybrid' authentication method;
*) ike1 - fixed memory leak on multiple CR payloads;
*) ipsec - added SHA384 hash algorithm support for phase 1;
*) lte - increased "at+cops" reply timeout to 90 seconds;
*) profile - added "lcd" process classificator;
*) tr069-client - fixed TotalBytesReceived parameter value;
*) winbox - added "src-mac-address" parameter under "IP/DHCP-Server/Leases" menu;
*) winbox - added missing IGMP Snooping settings to "Bridge" menu;
*) winbox - added missing MSTP settings to "Bridge" menu;
*) winbox - added support for LTE Cell Monitor;
*) wireless - increased "group-key-update" maximum value to 1 day;
*) wireless - updated "indonesia5" regulatory domain information;

**Nikiforos** · 09-03-21, 21:56

What's new in 6.49beta22 (2021-Mar-08 09:07):

Κώδικας:

Changes in this release:

*) bridge - added IGMP and MLD querier monitoring (CLI only);
*) bridge - added IGMP snooping log when multicast table gets full;
*) bridge - added MAC and IP source addresses information for DHCP snooping log;
*) bridge - improved bridge stability when host changes port (introduced in v6.47);
*) conntrack - increased total connection tracking table size based on installed RAM size;
*) console - require "write+ftp" permissions for executing script to file;
*) console - require "write+ftp" permissions for exporting configuration to file;
*) console - require "write+ftp" permissions for printing to file;
*) console - updated copyright notice;
*) crs3xx - correctly filter packets by L2MTU on 1Gbps Ethernet interfaces for CRS354 devices;
*) crs3xx - fixed interface flow control;
*) crs3xx - fixed interface LEDs for QSFP+ and SFP+ interfaces on CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - fixed SFP and SFP+ link rate reporting (introduced in v6.48beta11);
*) crs3xx - improved 1Gbps Ethernet port group traffic forwarding for CRS354 devices;
*) crs3xx - improved system stability when receiving large frames on CPU for CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) defconf - removed overlapping IPv6 firewall rules;
*) dhcp - fixed link state checking for DHCP client;
*) dhcpv6-server - check if pool name has changed from RADIUS on renew;
*) ethernet - improved system stability when receiving large VLAN tagged packets on IPQ4018/IPQ4019 devices;
*) firewall - fixed GRE protocol packets considered invalid when PPTP helper is disabled;
*) health - fixed voltage monitor on BaseBox5 devices;
*) ike2 - fixed DH group negotiation with EAP;
*) ike2 - fixed initial traffic selector's protocol and port in transport mode;
*) ipv6 - improved system stability when parsing IPv6 options;
*) lora - added additional predefined network servers;
*) m33g - removed 12..16 pins from "/system gpio" menu;
*) netinstall - fixed lock file persistence after reinstall;
*) poe - do not perform PoE firmware upgrade procedure on RB960 and OmniTik devices without PoE out;
*) ppp - do not fail "at-chat" command when issued on disabled PPP interface;
*) quickset - prefer 5GHz interface for WiFi scan in CPE mode;
*) rb922 - fixed miniPCI-e card detection (introduced in v6.49beta11);
*) supout - fixed "topic" column presence in "Log" section;
*) supout - print detailed list of active user sessions;
*) switch - improved resource allocation on 98PX1012 switch chip for CCR2004-1G-12S+2XS device;
*) swos - fixed "static-ip-address" parameter;
*) telnet - do not send options if connecting to non standard port;
*) telnet - fixed server when run on non standard port;
*) upgrade - improved "long-term" upgrade procedure on SMIPS devices;
*) user - fixed "skin" configuration for user groups (introduced in v6.48);
*) webfig - allow to specify "prefix" parameter under "IPv6/ND/Prefixes" menu;
*) webfig - do not corrupt settings when starting "Wireless Sniffer";
*) webfig - do not move top right menu in opposite direction when scrolling horizontally;
*) webfig - do not show newly created SMB shares as invalid;
*) webfig - do not show value units twice;
*) webfig - fixed interface sorting by name;
*) webfig - fixed new interface addition;
*) webfig - fixed "Wireless/CAP" menu opening;
*) webfig - show "Interfaces" menu by default after logging in;
*) webfig - show "network-mode" for LTE modems that support it;
*) webfig - show only "Close" button under "Wireless/Wireless Sniffer/Sniffed Packets" menu;
*) winbox - added "Channel" parameter under "System/Console" menu;
*) winbox - added "interface-speed-100G" LED type to "System/LEDs" menu;
*) winbox - fixed duplicate "Trusted" setting under "Interface/Bridge/Ports" menu;
*) winbox - fixed QCA-8511 switch chip type reporting under "Switch/Settings" menu;
*) winbox - fixed "reachable-time" value unit under "IPv6/ND" menu;
*) winbox - fixed support for "Delegated-IPv6-Prefix" for PPP services;
*) winbox - increased "target" field limit to 128 under "Queues" menu;
*) winbox - show "activity" column by default under "IP/Kid Control/Devices" menu;
*) winbox - show "LCD" only on boards that have LCD;
*) winbox - show "System/Health" only on boards that have health monitoring;
*) wireless - fixed minor typo in debug logging messages;
*) wireless - renamed "secondary-channel" to "secondary-frequency";
*) wireless - updated "united kingdom" regulatory domain information;

**deniSun** · 15-03-21, 17:23

6.49beta27 changelog:
Changes in this release:

Spoiler:

**deniSun** · 23-04-21, 15:59

6.49beta36 changelog:
Changes in this release:

Spoiler:

6.49beta38 changelog:
Changes in this release:

Spoiler:

**Nikiforos** · 16-05-21, 09:10

What's new in 6.49beta44 (2021-May-12 07:47):

Changes in this release:

*) bridge - fixed "vlan-encap" setting for filter and NAT rules;
*) crs3xx - fixed Ethernet LEDs after reboot for CRS354 devices;
*) health - added "phy-temperature" sensor monitoring for CRS312 device;
*) ike2 - added "MS-CHAP-Domain" attribute to RADIUS requests;
*) lte - fixed "earfcn" to band translation for "cell-monitor";
*) switch - fixed (R/M)STP port blocking right before switching them in HW bridge (fixes possible packet loop when changing bridge settings);
*) tile - fixed bridge performance degradation (introduced in v6.47);
*) winbox - show "System/Health" only on boards that have health monitoring;
*) wireless - improved system stability on several 802.11ac devices (introduced in v6.49beta36);
*) wireless - improve signaling of QCA9984 interface capabilities when using 160/80+80MHz channel width;
*) www - added "X-Frame-Options" header information to disallow website embedding in other pages;

**Nikiforos** · 19-05-21, 18:32

What's new in 6.49beta46 (2021-May-18 07:56):

Κώδικας:

Changes in this release:

!) wireless - fixed all affecting 'FragAttacks' vulnerabilities (CVE-2020-24587, CVE-2020-24588, CVE-2020-26144, CVE-2020-26146, CVE-2020-26147);
*) crs3xx - fixed packet forwarding on 1Gbps Ethernet interfaces for CRS354 devices (introduced in v6.49beta44);
*) dns - fixed CNAME query when target record is not in cache;
*) winbox - fixed health reporting on RB960, hEX, hEX S and hAP ac3 devices;

Other changes since v6.48.2:

*) bridge - added IGMP and MLD querier monitoring (CLI only);
*) bridge - added IGMP snooping log when multicast table gets full;
*) bridge - added MAC and IP source addresses information for DHCP snooping log;
*) bridge - fixed "vlan-encap" setting for filter and NAT rules;
*) bridge - improved system stability when disabling IGMP/MLD querier port (introduced in v6.49beta22);
*) bridge - improved system stability when using IGMP snooping and changing bridge MAC address;
*) chr - fixed OS provisioning on Azure;
*) chr - improved stability when changing "flow-control" settings on interfaces with e1000 drivers;
*) conntrack - increased total connection tracking table size based on installed RAM size;
*) console - require "write+ftp" permissions for executing script to file;
*) console - require "write+ftp" permissions for printing to file;
*) crs3xx - correctly filter packets by L2MTU on 1Gbps Ethernet interfaces for CRS354 devices;
*) crs3xx - fixed Ethernet LEDs after reboot for CRS354 devices;
*) crs3xx - fixed LEDs for QSFP+ interface on CRS326-24S+2Q+ device;
*) crs3xx - fixed SFP and SFP+ link rate reporting (introduced in v6.48beta11);
*) crs3xx - fixed VLAN priority removal for CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - fixed interface flow control;
*) crs3xx - fixed port-isolation on bonding interfaces for CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - improved LACP linking between CRS3xx series switches;
*) crs3xx - improved QSFP+ linking and mode changing for CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - improved packet transmit on SFP+ interfaces;
*) crs3xx - improved switch resource allocation for CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - improved system stability when receiving large frames on CPU for CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) defconf - fixed default configuration loading on RBOmniTikPG-5HacD;
*) defconf - fixed minor typo in configuration description;
*) defconf - removed overlapping IPv6 firewall rules;
*) defconf - use router as DNS server for DHCP hosts;
*) dhcpv6-server - check if pool name has changed from RADIUS on renew;
*) dhcpv6-server - improved dynamic server entry update;
*) dot1x - fixed "reject-vlan-id" for MAC authentication (introduced in v6.48);
*) dot1x - fixed MAC authentication fallback (introduced in v6.48);
*) firewall - fixed "ingress-priority" matcher;
*) firewall - fixed GRE protocol packets considered invalid when PPTP helper is disabled;
*) health - added "phy-temperature" sensor monitoring for CRS312 device;
*) ike2 - added "MS-CHAP-Domain" attribute to RADIUS requests;
*) ike2 - added support for ASN.1 DN "my-id" value setting for initiators;
*) ike2 - fixed initiator packet retransmit with DDOS cookie;
*) ipsec - fixed SA address parameter exporting;
*) ipsec - improved system stability on CHR;
*) ipsec - improved system stability on MMIPS devices;
*) lte - fixed "earfcn" to band translation for "cell-monitor";
*) m33g - removed 12..16 pins from "/system gpio" menu;
*) mipsbe - improved booting speed on non-NAND devices ("/system routerboard upgrade" required);
*) netinstall - fixed lock file persistence after reinstall;
*) netinstall - improved bootp packet handling on Linux netinstall-cli version when multiple NIC's are present;
*) ntp - use correct IPv6 multicast group for SNTP client;
*) package - always allow to uninstall package even if there is no free disk space left;
*) poe - fixed PoE out functionality on CRS354 (introduced in v6.49beta22);
*) ppp - improved stability when receiving bogus response on modem channel;
*) rb4011 - fixed SFP+ port MTU setting after link state change;
*) rb4011 - improved SFP+ port stability after boot-up;
*) rb922 - fixed miniPCI-e card detection (introduced in v6.49beta11);
*) route - improved stability when connected route is modified;
*) sfp - added "sfp-rate-select" setting (CLI only);
*) sfp - fixed GPON module linking (introduced in v6.47);
*) sfp - improved cable length monitoring as defined per SFF-8472 and SFF-8636;
*) sfp - improved link stability for 10G, 25G and 40G modules on CRS309, CRS312, CRS326-24S+2Q+ CRS354 and CCR2004 devices;
*) ssh - return proper error code from executed command;
*) supout - print detailed list of active user sessions;
*) switch - fixed (R/M)STP port blocking right before switching them in HW bridge (fixes possible packet loop when changing bridge settings);
*) switch - improved packet transmit between CPU and 98PX1012 for CCR2004-1G-12S+2XS device;
*) swos - fixed "static-ip-address" parameter;
*) system - improved resource allocation (improves several service stability e.g. HTTPS, PPPoE, VPN);
*) tile - fixed bridge performance degradation (introduced in v6.47);
*) tr069-client - added "X_MIKROTIK_LinkDowns" parameter for interface "link-downs" value reporting;
*) upgrade - fixed free space checking on flash type memories when installing new packages;
*) w60g - improved stability in low temperature environments;
*) webfig - do not show value units twice;
*) webfig - fixed "PortMapping" button (introduced in v6.48.2);
*) webfig - fixed "Wireless/CAP" menu opening;
*) webfig - fixed interface sorting by name;
*) webfig - show only "Close" button under "Wireless/Wireless Sniffer/Sniffed Packets" menu;
*) winbox - added "interface-speed-100G" LED type to "System/LEDs" menu;
*) winbox - fixed support for "Delegated-IPv6-Prefix" for PPP services;
*) winbox - show "System/Health" only on boards that have health monitoring;
*) wireless - do not send packet back to station-bridge it was received from;
*) wireless - fixed issue with multicast traffic delivery to client devices using power-save;
*) wireless - fixed minor typo in debug logging messages;
*) wireless - improve WMM priority assignment for packets with internal priority greater than 7;
*) wireless - improve regulatory compliance with DFS requirements;
*) wireless - improve signaling of QCA9984 interface capabilities when using 160/80+80MHz channel width;
*) wireless - improved system stability on several 802.11ac devices (introduced in v6.49beta36);
*) wireless - renamed "secondary-channel" to "secondary-frequency";
*) wireless - updated "united kingdom" regulatory domain information;
*) www - added "X-Frame-Options" header information to disallow website embedding in other pages;

**deniSun** · 24-09-21, 14:13

What's new in 6.49rc1 (2021-Sep-23 12:32):

Changes since last beta release:

*) backup - fixed backup file restore (introduced in v6.49beta);
*) branding - fixed LCD logo loading from branding package when installed via Netinstall;
*) branding - properly clean up old branding files before installing a new one;
*) bridge - added IGMP and MLD querier monitoring;
*) bridge - improved stability when quickly adding and removing bridge interface;
*) crs3xx - fixed default MAC address calculation on management Ethernet for CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - improved system stability when learning MDB and FBD entries for CRS312, CRS326-24S+2Q+ and CRS354 devices (introduced in v6.49beta44);
*) dhcpv4-server - reset lease's dynamic "bcast" flag on packets from relay;
*) gps - improved interface monitoring;
*) health - improved temperature reporting;
*) kid-control - improved IPv6 firewall rule generation;
*) leds - fixed LTE LED default mapping for wAP R ac LTE kit;
*) lora - added additional predefined network servers;
*) lora - fixed "PULL_DATA" token generation;
*) mpls - allow to disable FastPath (CLI only);
*) mqtt - added server name indication;
*) netinstall - require Netinstall version to be the same or newer as "factory-software";
*) poe - update PoE firmware only on devices that supports it;
*) qsfp - improved system stability when setting unsupported link rates;
*) routerboard - fixed "reformat-hold-button-max" validation for values below 10s;
*) sfp - improved SFP, SFP+, SFP28 and QSFP+ interface stability for CRS3xx and CCR2004 devices;
*) sfp28 - changed FEC auto mode to disabled;
*) tr069-client - fixed traceroute diagnostics time values;
*) tr069-client - improved XML with new-lines for readable output;
*) w60g - limit power output when using region EU to match EN302567 on nRAY;
*) w60g - use EU region by default;
*) winbox - added "dhcp" option to "multicast-helper" setting;
*) winbox - do not allow to add/remove W60G interfaces;
*) winbox - separated CCQ Tx and Rx values in their own unique columns;
*) winbox - show "System/Health/Settings" only on boards that have configurable values;
*) winbox - show "current-channel" column by default for CAP interfaces;
*) wireless - added U-NII-2 support for US and Canada country profiles for hAP ac lite;
*) wireless - do not remove channels >2462 MHz from "scanlist" if scanning for fixed channel;
*) wireless - log client signal strength on disconnect;
*) wireless - updated "israel" regulatory domain information;

**deniSun** · 29-09-21, 14:14

6.49rc2 changelog:
Changes in this release:

*) bridge - improved controller bridge stability when adding RouterOS v7 port extender;
*) bridge - improved port extender stability when creating bond interfaces on excluded ports;
*) crs3xx - fixed bridge controller and extender packet forwarding for CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) dhcp-server - fixed DHCP Option decimal value parsing;
*) discovery - do not send discovery packets on interfaces that are blocked by STP (introduced in v6.48);
*) sfp - added "sfp-rate-select" setting;
*) supout - added controller bridge section;
*) switch - fixed (R/M)STP port blocking right before switching them in HW bridge (fixes possible packet loop when changing bridge settings);
*) user - added "expired" user status with suggestion to change password (WinBox v3.29 required);
*) user - fixed active user session purging on disconnect;
*) user - show "expired password" prompt for users with blank password;
*) winbox - added "fec-mode" parameter under "Interface/Ethernet" menu;
*) winbox - minimal required version is v3.30;
*) wireless - improved system stability when sending packets through interface after L2MTU is increased;

**deniSun** · 23-03-22, 17:10

What's new in 7.2rc5 (2022-Mar-23 12:04):

Spoiler:

*) api - accept "Content-Type" with specified charset;
*) arm - fixed "auto" CPU frequency setting;
*) arm64 - improved Watchdog initiated reboot reason reporting;
*) backup - fixed cloud backup's creation timezone;
*) bgp - added BGP advertisements display (requires output.keep-sent-attributes to be set);
*) bgp - fixed link-local iBGP address selection;
*) bgp - fixed network advertisement from address-lists after reboot;
*) bridge - fixed firewall "ingress-priority" matcher and "new-priority=from-ingress" action settings from VLAN tagged frames;
*) ccr2004 - improved system stability on CCR2004-12S+2XS;
*) crs1xx/2xx - fixed static switch host addresses after link down;
*) crs1xx/2xx - ignore static bridge host addresses (switch unicast-fdb should be used instead);
*) dhcpv6 - added VRF support;
*) dude - fixed The Dude client compatibility with RouterOS v7;
*) firewall - improved available port lookup for source NAT when free port range is exhausted;
*) ipsec - fixed "identities" menu emptying after RouterOS upgrade/reboot;
*) ipv6 - do not add duplicate dynamic prefix when static already exists;
*) ipv6 - fixed "retransmissit-interval" unit value;
*) ipv6 - fixed VLAN tagged PPPoE packet receiving on RB5009;
*) l2tp - fixed CHAP challenge packet processing over IPsec;
*) l3hw - improved routing table offloading for CRS305, CRS326-24G-2S+, CRS328, netPower, netFiber devices;
*) led - fixed LED behavior on Audience;
*) led - reduced LTE signal LED range to -70;
*) log - added warning message when connection tracking table is full;
*) lte - add IPv6 address on interface as well;
*) lte - added support for Uplink CA reporting;
*) lte - changed "CS/PS" registration type from "both" to "any" on R11e-LTE un R11e-LTE6;
*) lte - do not loose "band" configuration after reboot on Chateau 5G;
*) lte - fixed AT command response handling on R11e-LTE;
*) lte - fixed MBIM modem reset on AT timeout;
*) lte - fixed link flapping when loosing cellular signal on R11e-LTE un R11e-LTE6;
*) ntp - improved service stability when none of the NTP servers are reachable for a while;
*) ospf - general stability improvements;
*) ospf - improved DB retransmit logging;
*) ospf - send notifies for neighbors;
*) ovpn - improved memory allocation on Tile in "ethernet" mode;
*) ovpn - improved system stability in high load scenarios;
*) pimsm - fixed menu prints;
*) pimsm - general stability improvements;
*) queue - fixed queued IPv6 traffic considered as "invalid" by Firewall;
*) rb4011 - fixed jumbo frame processing on SFP+ port when using 1G module;
*) rip - added logging;
*) rip - fixed route metrics;
*) rip - fixed route redistribution;
*) rip - use nexthop with interface;
*) route - fixed "table" menu emptying after RouterOS upgrade;
*) route - fixed BGP atomic aggregate value;
*) route - fixed ECMP route removal;
*) route - general stability improvements;
*) routerboard - fixed "ether2" interface presence on some RBwAPGR devices;
*) routerboard - fixed WPS button functionality on Audience;
*) routing - added PCAP viewer tool for BGP advertisements debugging purposes;
*) routing-filter - fixed "bgp-*-communities-empty" matcher;
*) sfp - improved SFP module detection on CRS106 and CRS112;
*) smips - improved RAM allocation;
*) switch - added "rx-overflow" counter for 88E6393X (RB5009) and 88E6191X (CCR2004-16G-2S+) switch chips;
*) switch - improved packet forwarding with enabled "cpu-flow-control" setting between different rate interfaces for 88E6393X (RB5009) and 88E6191X (CCR2004-16G-2S+) switch chips;
*) tr069-client - added support for 5G band configuration;
*) tr069-client - added support for wireless "skip-DFS" configuration;
*) winbox - added missing "3GGP RAW" parameter under "Interface/Wireless/Interworking Profile" menu;
*) winbox - added missing "accounting", "interim-update" and "radius-password" parameters under "IP/DHCP Server" menu;
*) winbox - allow adding more than 100 tagged/untagged interfaces under "Bridge/VLAN" menu;
*) winbox - allow configuring "VTEP" under "Interface/VXLAN" menu;
*) winbox - fixed "00:00:00" time printing;
*) winbox - fixed switch related settings for MT7621 switch chip (hEX, hEX S, RBM33G, RBM11G, LtAP);
*) winbox - moved IPv4 and IPv6 "Rules" menus under "Routing" menu;
*) winbox - properly show "v" flag instead of "y" under "IP/Route" menu;
*) winbox - properly update server list under "System/NTP Client/Servers" menu;
*) winbox - show "System/Health/Settings" only on boards that have configurable values;
*) www - fixed "tls-version" for SSL;
*) x86 - allow to select disk for install image;
*) x86 - fixed NVME partition path;
*) zerotier - fixed IPv6 support;

Θέμα: Mikrotik ROS RC version συζητήσεις-bugs κτλ.

Παρόμοια Θέματα

Περί ROS ο λόγος...

Aποστολή και λήψη SMS στο Mikrotik ROS

Mikrotik SSTP server

Mikrotik x86 vs RB3011UiAS-RM

Ενεργοποίηση ipv6 σε Mikrotik πίσω απο router παρόχου

Bookmarks

Bookmarks

Δικαιώματα - Επιλογές