Login Form
IPv6 Ready
Εμφάνιση 1-13 από 13
  1. #1
    Εγγραφή
    23-01-2014
    Περιοχή
    aigina
    Μηνύματα
    12
    Downloads
    0
    Uploads
    0
    Τύπος
    ADSL2+
    Ταχύτητα
    16384/1024
    ISP
    ΟΤΕ Conn-x
    DSLAM
    ΟΤΕ - ΑΙΓΙΝΑ
    Router
    draytek 2860
    Γεια σας, εχω το εξης θεμα, αγορασα ενα κεντρο voip το yeastar s20 το εχω σεταρει κανονικα δλδ εσωτερικα δουλευουν ολα ενδοκλησεις ειναι οκ, η pstn εισερχομενη εξερχομενη δουλευει κανονικα, στην γραμμη που εχω την voip συνδεση yuboto εχω εισερχομενη δεν μπορω να βγαλω εξερχομενη η γραμμη δουλευει κανονικα στο cisco uc 540 την δοκιμασα, μηπως ειχε θεμα η γραμμη. κατι πιστευω με ρυθμυση του κεντρου εχει να κανει, εχω ψαξει forum, εχω φαει ωρες ενα καρο ρυθμισεις, αλλα δεν βγαινει εξερχομενη, αν καποιος εχει αντιμετωπησει κατι παρομοιο και μπορει να βοηθησει, ας γραψει εδω, ευχαριστω.

  2. #2
    Εγγραφή
    18-03-2018
    Μηνύματα
    62
    Downloads
    0
    Uploads
    0
    ISP
    Forthnet
    Δοκίμασε να φτιάξεις το outbound route με πρόθεμα. Δηλαδή

    dial pattern *162XXXXXXXXX
    strip 3
    member trunks το yuboto
    member extensions όλα τα εσωτερικά σου.

  3. #3
    Εγγραφή
    23-01-2014
    Περιοχή
    aigina
    Μηνύματα
    12
    Downloads
    0
    Uploads
    0
    Τύπος
    ADSL2+
    Ταχύτητα
    16384/1024
    ISP
    ΟΤΕ Conn-x
    DSLAM
    ΟΤΕ - ΑΙΓΙΝΑ
    Router
    draytek 2860
    κανει το ιδιο, δλδ παιρνεις τον αριθμο και δινει αμεσως σημα κατειλημενου, σε ευχαριστω παντως, καθε ιδεα ευπροσδεκτη.

  4. #4
    Εγγραφή
    18-03-2018
    Μηνύματα
    62
    Downloads
    0
    Uploads
    0
    ISP
    Forthnet
    Ανέβασε screen shots με το πώς έχεις στημένο το yuboto trunk (κρύβοντας φυσικά τα user, pass). Αν έχει κάποιο log και αυτό ανέβασε.

  5. #5
    Εγγραφή
    23-01-2014
    Περιοχή
    aigina
    Μηνύματα
    12
    Downloads
    0
    Uploads
    0
    Τύπος
    ADSL2+
    Ταχύτητα
    16384/1024
    ISP
    ΟΤΕ Conn-x
    DSLAM
    ΟΤΕ - ΑΙΓΙΝΑ
    Router
    draytek 2860
    Πατήστε στην εικόνα για να τη δείτε σε μεγέθυνση. 

Όνομα:  s20.jpg 
Εμφανίσεις:  15 
Μέγεθος:  90,8 KB 
ID: 193843

    αν θελεις κατι αλλο πες μου να στειλω.

  6. #6
    Εγγραφή
    18-03-2018
    Μηνύματα
    62
    Downloads
    0
    Uploads
    0
    ISP
    Forthnet
    Παράθεση Αρχικό μήνυμα από hxooptiki Εμφάνιση μηνυμάτων
    Πατήστε στην εικόνα για να τη δείτε σε μεγέθυνση. 

Όνομα:  s20.jpg 
Εμφανίσεις:  15 
Μέγεθος:  90,8 KB 
ID: 193843

    αν θελεις κατι αλλο πες μου να στειλω.
    Δοκίμασε να κάνεις ενεργό το outbound proxy με την ip της yubo και πόρτα την 5070.

  7. #7
    Εγγραφή
    23-01-2014
    Περιοχή
    aigina
    Μηνύματα
    12
    Downloads
    0
    Uploads
    0
    Τύπος
    ADSL2+
    Ταχύτητα
    16384/1024
    ISP
    ΟΤΕ Conn-x
    DSLAM
    ΟΤΕ - ΑΙΓΙΝΑ
    Router
    draytek 2860
    το εχω κανει αλλα τιποτα, μολις παρεις το νουμερο που θελεις παει να ξεκινησει και ριχνει την γραμμη, ειτε βαλω outbound proxy ειτε οχι. οπου εχω κοιταξει σε αλλα σαιτ η φορουμ ειναι σωστες οι ρυθμισεις που κανω αλλα τιποτα, δεν μπορω να βρω τι φταει με την pstn ολα καλα με την sip μονο εισερχομενη εχω.

  8. #8
    Εγγραφή
    18-03-2018
    Μηνύματα
    62
    Downloads
    0
    Uploads
    0
    ISP
    Forthnet
    Παράθεση Αρχικό μήνυμα από hxooptiki Εμφάνιση μηνυμάτων
    το εχω κανει αλλα τιποτα, μολις παρεις το νουμερο που θελεις παει να ξεκινησει και ριχνει την γραμμη, ειτε βαλω outbound proxy ειτε οχι. οπου εχω κοιταξει σε αλλα σαιτ η φορουμ ειναι σωστες οι ρυθμισεις που κανω αλλα τιποτα, δεν μπορω να βρω τι φταει με την pstn ολα καλα με την sip μονο εισερχομενη εχω.
    Από codecs τι έχεις βάλει για την yubo;

    - - - Updated - - -

    Log file

    Ανέβασε το κρύβοντας τα στοιχεία σου.

  9. #9
    Εγγραφή
    23-01-2014
    Περιοχή
    aigina
    Μηνύματα
    12
    Downloads
    0
    Uploads
    0
    Τύπος
    ADSL2+
    Ταχύτητα
    16384/1024
    ISP
    ΟΤΕ Conn-x
    DSLAM
    ΟΤΕ - ΑΙΓΙΝΑ
    Router
    draytek 2860
    g729 που προτεινει η yuboto

    - - - Updated - - -

    login as: support
    support@IPPBX:~$ asterisk -vvvvvvvvvvvvvr
    Unable to open specified codec config file '/ysdisk/ysapps/pbxcenter/etc/codec.conf', using built-in defaults
    Unable to disable core size resource limit: Operation not permitted
    Asterisk 13.7.0, Copyright (C) 1999 - 2014, Digium, Inc. and others.
    Created by Mark Spencer <markster@digium.com>
    Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty' for details.
    This is free software, with components licensed under the GNU General Public
    License version 2 and other licenses; you are welcome to redistribute it under
    certain conditions. Type 'core show license' for details.
    =========================================================================
    Connected to Asterisk 13.7.0 currently running on IPPBX (pid = 2073)
    No entry for terminal type "xterm";
    using dumb terminal settings.
    [2018-05-21 13:10:50] NOTICE[2093]: ysscale.c:1130 usb_exception_func: Total recv 600 heartbeat packets from USB port 0

    == Parsing '/etc/asterisk/pjsip.conf': Found
    == Parsing '/etc/asterisk/pjsip_auth.conf': Found

    == Parsing '/etc/asterisk/pjsip_wizard.conf': Found

    == Parsing '/etc/asterisk/pjsip.conf': Found
    == Parsing '/etc/asterisk/pjsip_auth.conf': Found

    == Parsing '/etc/asterisk/pjsip_wizard.conf': Found

    IPPBX*CLI> Direct Outward Dialing Number
    No such command 'Direct Outward Dialing Number' (type 'core show help Direct Outward' for other possible commands)

    == Parsing '/etc/asterisk/pjsip.conf': Found
    == Parsing '/etc/asterisk/pjsip_auth.conf': Found

    == Parsing '/etc/asterisk/pjsip_wizard.conf': Found

    -- Starting simple switch on 'DAHDI/1-1'

    [2018-05-21 13:12:11] WARNING[8017][C-00000001]: chan_dahdi.c:5613 dahdi_ec_enable: Enabled echo cancellation on channel 1

    -- Executing [96xxxxxxxxx@DLPN_DialPlan100:1] YsWalkContext("DAHDI/1-1", "blacklist-outbound,69xxxxxxxx,1,100,outbound") in new stack

    -- Executing [969xxxxxxx@DLPN_DialPlan100:2] NoOp("DAHDI/1-1", "No Pinset") in new stack

    -- Executing [969xxxxxxx@DLPN_DialPlan100:3] Set("DAHDI/1-1", "ORGINEXTEN=969xxxxxxxx") in new stack

    -- Executing [969xxxxxxxxx@DLPN_DialPlan100:4] Set("DAHDI/1-1", "ORGINROUTE=sip_xxxxx_yuboto") in new stack

    -- Executing [969xxxxxxx@DLPN_DialPlan100:5] Set("DAHDI/1-1", "ORGINCONTEXT=DLPN_DialPlan100") in new stack

    -- Executing [969xxxxxxx@DLPN_DialPlan100:6] Set("DAHDI/1-1", "MRMEMORYHUNT=no") in new stack

    -- Executing [969xxxxxxx@DLPN_DialPlan100:7] GetNextOutRouter("DAHDI/1-1", "sip_29079_yuboto,969xxxxxxxx") in new stack

    -- Executing [969xxxxxxxx@DLPN_DialPlan100:8] Goto("DAHDI/1-1", "a1") in new stack

    -- Goto (DLPN_DialPlan100,969xxxxxxxx,11)

    -- Executing [969xxxxxxxxx@DLPN_DialPlan100:11] NoOp("DAHDI/1-1", "NO ADJUST") in new stack

    -- Executing [969xxxxxxxxxx@DLPN_DialPlan100:12] Macro("DAHDI/1-1", "trunkdial-failover-0.3,1,,69xxxxxxxx,trunk-sip_29079_yuboto-endpoint") in new stack

    -- Executing [s@macro-trunkdial-failover-0.3:1] NoOp("DAHDI/1-1", "do call out") in new stack

    -- Executing [s@macro-trunkdial-failover-0.3:2] GotoIf("DAHDI/1-1", "0?5:3") in new stack

    -- Goto (macro-trunkdial-failover-0.3,s,3)

    -- Executing [s@macro-trunkdial-failover-0.3:3] GotoIf("DAHDI/1-1", "0?4:5") in new stack

    -- Goto (macro-trunkdial-failover-0.3,s,5)

    -- Executing [s@macro-trunkdial-failover-0.3:5] Set("DAHDI/1-1", "TCOUNT=4") in new stack

    -- Executing [s@macro-trunkdial-failover-0.3:6] Set("DAHDI/1-1", "CDR(userfield)=Outbound") in new stack

    -- Executing [s@macro-trunkdial-failover-0.3:7] Set("DAHDI/1-1", "CDR(extfield4)=") in new stack

    [2018-05-21 13:12:11] WARNING[2106]: func_cdr.c:352 cdr_write_callback: CDR requires a value (CDR(variable)=value)
    )
    -- Executing [s@macro-trunkdial-failover-0.3:8] Set("DAHDI/1-1", "OLDCALLERID=100") in new stack

    -- Executing [s@macro-trunkdial-failover-0.3:9] Set("DAHDI/1-1", "TOUCH_MONITOR=100-6976214466") in new stack

    -- Executing [s@macro-trunkdial-failover-0.3:10] NoOp("DAHDI/1-1", "302297029079") in new stack

    -- Executing [s@macro-trunkdial-failover-0.3:11] Set("DAHDI/1-1", "TIMEOUT(absolute)=6000") in new stack

    -- Channel will hangup at 2018-05-21 14:52:11.790 EEST.

    -- Executing [s@macro-trunkdial-failover-0.3:12] Set("DAHDI/1-1", "DLSTAT=UNKNOW") in new stack

    -- Executing [s@macro-trunkdial-failover-0.3:13] GotoIf("DAHDI/1-1", "1>0?1-dial,1") in new stack

    -- Goto (macro-trunkdial-failover-0.3,1-dial,1)

    -- Executing [1-dial@macro-trunkdial-failover-0.3:1] GotoIf("DAHDI/1-1", "0?nextrouter,1") in new stack

    [2018-05-21 13:12:11] WARNING[8017][C-00000001]: ast_expr2.fl:470 ast_yyerror: ast_yyerror(): syntax error: syntax error, unexpected '>', expecting $end; Input:
    > 0
    ^

    [2018-05-21 13:12:11] WARNING[8017][C-00000001]: ast_expr2.fl:474 ast_yyerror: If you have questions, please refer to https://wiki.asterisk.org/wiki/displ...nnel+Variables

    -- Executing [1-dial@macro-trunkdial-failover-0.3:2] GotoIf("DAHDI/1-1", "?1-dial,6:1-dial,3") in new stack

    -- Goto (macro-trunkdial-failover-0.3,1-dial,3)

    -- Executing [1-dial@macro-trunkdial-failover-0.3:3] GotoIf("DAHDI/1-1", "0?setdod,1:setdodname,1") in new stack

    -- Goto (macro-trunkdial-failover-0.3,setdodname,1)

    -- Executing [setdodname@macro-trunkdial-failover-0.3:1] GotoIf("DAHDI/1-1", "0?setdod,3:1-dial,4") in new stack

    -- Goto (macro-trunkdial-failover-0.3,1-dial,4)

    -- Executing [1-dial@macro-trunkdial-failover-0.3:4] ExecIf("DAHDI/1-1", "1?Set(SRCNUMBER=100):Set(SRCNUMBER=)") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:5] GotoIf("DAHDI/1-1", "1?setdodnum,1:1-dial,6") in new stack

    -- Goto (macro-trunkdial-failover-0.3,setdodnum,1)

    -- Executing [setdodnum@macro-trunkdial-failover-0.3:1] Set("DAHDI/1-1", "CALLERID(name)=yuboto") in new stack

    -- Executing [setdodnum@macro-trunkdial-failover-0.3:2] Set("DAHDI/1-1", "CALLERID(num)=3022970xxxxxx") in new stack

    -- Executing [setdodnum@macro-trunkdial-failover-0.3:3] Set("DAHDI/1-1", "CDR(extfield3)=3022970xxxxxx") in new stack

    -- Executing [setdodnum@macro-trunkdial-failover-0.3:4] Goto("DAHDI/1-1", "1-dial,6") in new stack

    -- Goto (macro-trunkdial-failover-0.3,1-dial,6)

    -- Executing [1-dial@macro-trunkdial-failover-0.3:6] Set("DAHDI/1-1", "OUTDIALOPT=tTKkWwXxb(add_diversion,add_diversion,1)") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:7] Set("DAHDI/1-1", "FAXOPT(gateway)=no") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:8] NoOp("DAHDI/1-1", "NO CLIP") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:9] Set("DAHDI/1-1", "PJSIP_ACCOUNT=") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:10] Set("DAHDI/1-1", "PJSIP_TRUNK=@trunk-sip_29079_yuboto-endpoint") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:11] Set("DAHDI/1-1", "YSGSM_TRUNK=") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:12] Set("DAHDI/1-1", "DIALSTRING=") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:13] GotoIf("DAHDI/1-1", "0?1-dial,15") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:14] Set("DAHDI/1-1", "DIALSTRING=PJSIP/697xxxxxxxx@trunk-sip_29079_yuboto-endpoint") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:15] GotoIf("DAHDI/1-1", "0?sys-dial,1") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:16] ExecIf("DAHDI/1-1", "0?SetGlobal(LastTrunkOfsip_29079_yuboto=trunk-sip_29079_yuboto-endpoint):Noop(Not Mrmemory Hunt)") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:17] ExecIf("DAHDI/1-1", "0?Set(JITTERBUFFER(disabled)=):NoOp(No Jitter Buffer)") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:18] ExecIf("DAHDI/1-1", "1?Set(JITTERBUFFER(disabled)=):NoOp(No Jitter Buffer)") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:19] ExecIf("DAHDI/1-1", "0?Set(JITTERBUFFER(disabled)=):NoOp(No Jitter Buffer)") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:20] GotoIf("DAHDI/1-1", "1?1-dial,21:1-dial,23") in new stack

    -- Goto (macro-trunkdial-failover-0.3,1-dial,21)

    -- Executing [1-dial@macro-trunkdial-failover-0.3:21] Set("DAHDI/1-1", "GROUP()=trunk-sip_29079_yuboto-endpoint") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:22] GotoIf("DAHDI/1-1", "0?2-dial,1") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:23] GotoIf("DAHDI/1-1", "0?forking:outbound-dial") in new stack

    -- Goto (macro-trunkdial-failover-0.3,1-dial,25)

    -- Executing [1-dial@macro-trunkdial-failover-0.3:25] Dial("DAHDI/1-1", "PJSIP/696xxxxxxxxxx@trunk-sip_29079_yuboto-endpoint,,tTKkWwXxb(add_diversion,add_diversion,1)") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:26] NoOp("DAHDI/1-1", "YSCHANUNAVAIL") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:27] GotoIf("DAHDI/1-1", "0>1?meetme-invite,1") in new stack

    -- Executing [1-dial@macro-trunkdial-failover-0.3:28] Goto("DAHDI/1-1", "1-YSCHANUNAVAIL,1") in new stack

    -- Goto (macro-trunkdial-failover-0.3,1-YSCHANUNAVAIL,1)

    -- Executing [1-YSCHANUNAVAIL@macro-trunkdial-failover-0.3:1] GotoIf("DAHDI/1-1", "0?4") in new stack

    -- Executing [1-YSCHANUNAVAIL@macro-trunkdial-failover-0.3:2] Set("DAHDI/1-1", "DLSTAT=9-YSCHANUNAVAIL") in new stack

    -- Executing [1-YSCHANUNAVAIL@macro-trunkdial-failover-0.3:3] Goto("DAHDI/1-1", "2-dial,1") in new stack

    -- Goto (macro-trunkdial-failover-0.3,2-dial,1)

    -- Executing [2-dial@macro-trunkdial-failover-0.3:1] Set("DAHDI/1-1", "TCOUNT=5") in new stack

    -- Executing [2-dial@macro-trunkdial-failover-0.3:2] Goto("DAHDI/1-1", "1-dial,1") in new stack

    -- Goto (macro-trunkdial-failover-0.3,1-dial,1)

    -- Executing [1-dial@macro-trunkdial-failover-0.3:1] GotoIf("DAHDI/1-1", "1?nextrouter,1") in new stack

    -- Goto (macro-trunkdial-failover-0.3,nextrouter,1)

    -- Executing [nextrouter@macro-trunkdial-failover-0.3:1] GotoIf("DAHDI/1-1", "0?,969xxxxxxxxx,1:addevent,1") in new stack

    -- Goto (macro-trunkdial-failover-0.3,addevent,1)

    -- Executing [addevent@macro-trunkdial-failover-0.3:1] GotoIf("DAHDI/1-1", "0?4:2") in new stack

    -- Goto (macro-trunkdial-failover-0.3,addevent,2)

    -- Executing [addevent@macro-trunkdial-failover-0.3:2] Set("DAHDI/1-1", "EVENTCONTEXT=provider=trunk-sip_xxxxxx_yuboto-endpoint&destnumber=69xxxxxxx&srcnumber=3022970xxxxxxx") in new stack

    -- Executing [addevent@macro-trunkdial-failover-0.3:3] AGI("DAHDI/1-1", "/ysbin/eventadd,2002,provider=trunk-sip_29079_yuboto-endpoint&destnumber=xxxxxxxx&srcnumber=3022970xxxxxx") in new stack

    -- Launched AGI Script /ysbin/eventadd

    -- <DAHDI/1-1>AGI Script /ysbin/eventadd completed, returning 0

    -- Executing [addevent@macro-trunkdial-failover-0.3:4] Goto("DAHDI/1-1", "9-YSCHANUNAVAIL,1") in new stack

    -- Goto (macro-trunkdial-failover-0.3,9-YSCHANUNAVAIL,1)

    -- Executing [9-YSCHANUNAVAIL@macro-trunkdial-failover-0.3:1] Goto("DAHDI/1-1", "9-CONGESTION,3") in new stack

    -- Goto (macro-trunkdial-failover-0.3,9-CONGESTION,3)

    -- Executing [9-CONGESTION@macro-trunkdial-failover-0.3:3] UserEvent("DAHDI/1-1", "CallFailed,Cause: Line unreachable") in new stack

    [2018-05-21 13:12:12] WARNING[8017][C-00000001]: ast_expr2.fl:470 ast_yyerror: ast_yyerror(): syntax error: syntax error, unexpected '=', expecting $end; Input:
    =YES
    ^

    [2018-05-21 13:12:12] WARNING[8017][C-00000001]: ast_expr2.fl:474 ast_yyerror: If you have questions, please refer to https://wiki.asterisk.org/wiki/displ...nnel+Variables

    -- Executing [9-CONGESTION@macro-trunkdial-failover-0.3:4] GotoIf("DAHDI/1-1", "?6") in new stack

    -- Executing [9-CONGESTION@macro-trunkdial-failover-0.3:5] Playback("DAHDI/1-1", "record/") in new stack

    [2018-05-21 13:12:12] WARNING[8017][C-00000001]: file.c:902 ast_openstream_full: File record/ does not exist in any format

    [2018-05-21 13:12:12] WARNING[8017][C-00000001]: file.c:1232 ast_streamfile: Unable to open record/ (format (ulaw)): No such file or directory

    -- Executing [9-CONGESTION@macro-trunkdial-failover-0.3:6] Hangup("DAHDI/1-1", "") in new stack

    == Spawn extension (macro-trunkdial-failover-0.3, 9-CONGESTION, 6) exited non-zero on 'DAHDI/1-1' in macro 'trunkdial-failover-0.3'

    == Spawn extension (DLPN_DialPlan100, 969xxxxxxxx, 12) exited non-zero on 'DAHDI/1-1'

    -- Executing [h@DLPN_DialPlan100:1] Hangup("DAHDI/1-1", "") in new stack

    == Spawn extension (DLPN_DialPlan100, h, 1) exited non-zero on 'DAHDI/1-1'

    [2018-05-21 13:12:12] WARNING[8017][C-00000001]: chan_dahdi.c:5657 dahdi_ec_disable: Disabled echo cancellation on channel 1

    -- Hanging up on 'DAHDI/1-1'

    -- Hungup 'DAHDI/1-1'

    == Parsing '/etc/asterisk/pjsip.conf': Found
    == Parsing '/etc/asterisk/pjsip_auth.conf': Found

    == Parsing '/etc/asterisk/pjsip_wizard.conf': Found

    -- Starting simple switch on 'DAHDI/1-1'

    -- Hanging up on 'DAHDI/1-1'
    -- Hungup 'DAHDI/1-1'

    [2018-05-21 13:12:30] NOTICE[2093]: ysscale.c:1130 usb_exception_func: Total recv 700 heartbeat packets from USB port 0

    IPPBX*CLI> Direct Outward Dialing NumberDirect Outward Dialing Number

  10. #10
    Εγγραφή
    18-03-2018
    Μηνύματα
    62
    Downloads
    0
    Uploads
    0
    ISP
    Forthnet
    Δοκίμασε με codec alaw και μετά με σκέτο sip, όχι pjsip (αν το υποστηρίζει το κέντρο) σαν trunk.

  11. #11
    Εγγραφή
    23-01-2014
    Περιοχή
    aigina
    Μηνύματα
    12
    Downloads
    0
    Uploads
    0
    Τύπος
    ADSL2+
    Ταχύτητα
    16384/1024
    ISP
    ΟΤΕ Conn-x
    DSLAM
    ΟΤΕ - ΑΙΓΙΝΑ
    Router
    draytek 2860
    το δοκιμασα αλλα το ιδιο, pjsip δεν υποστηριζει, δεν ξερω μου κανει εντυπωση το trunk που εχω το κουμπωνω πανω στο cisco uc540 Και παιζει αερα, την δοκιμαζω σε ενα αλλο linksys cisco παιζει, πανω σε yeastar mypbx soho μια χαρα, εδω δεν μπορω να βρω τι τρεχει.

    - - - Updated - - -

    αλλαξα το ονομα του καλουντος στο trunk, επαιξε μια φορα και παλι κανει τα ιδια.

  12. #12
    Εγγραφή
    18-03-2018
    Μηνύματα
    62
    Downloads
    0
    Uploads
    0
    ISP
    Forthnet
    Ξανά μπες στο asterisk cli και δώσε
    Κώδικας:
    sip set debug ip 213.144.173.77
    κάνε την εξερχόμενη κλήση και μετά δώσε
    Κώδικας:
    sip set debug off
    κρύψε τα τηλέφωνα σου και ανέβασε το.

  13. #13
    Εγγραφή
    23-01-2014
    Περιοχή
    aigina
    Μηνύματα
    12
    Downloads
    0
    Uploads
    0
    Τύπος
    ADSL2+
    Ταχύτητα
    16384/1024
    ISP
    ΟΤΕ Conn-x
    DSLAM
    ΟΤΕ - ΑΙΓΙΝΑ
    Router
    draytek 2860
    login as: support
    support@192.168.2.63's password:
    support@IPPBX:~$ asterisk -vvvvvvvvvvvvvr
    Unable to open specified codec config file '/ysdisk/ysapps/pbxcenter/etc/codec.conf', using built-in defaults
    Unable to disable core size resource limit: Operation not permitted
    Asterisk 13.7.0, Copyright (C) 1999 - 2014, Digium, Inc. and others.
    Created by Mark Spencer <markster@digium.com>
    Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty' for details.
    This is free software, with components licensed under the GNU General Public
    License version 2 and other licenses; you are welcome to redistribute it under
    certain conditions. Type 'core show license' for details.
    =========================================================================
    Connected to Asterisk 13.7.0 currently running on IPPBX (pid = 2094)
    No entry for terminal type "xterm";
    using dumb terminal settings.
    [2018-05-23 16:13:12] NOTICE[2114]: ysscale.c:1130 usb_exception_func: Total recv 2100 heartbeat packets from USB port 0

    == Parsing '/etc/asterisk/pjsip.conf': Found
    == Parsing '/etc/asterisk/pjsip_auth.conf': Found

    == Parsing '/etc/asterisk/pjsip_wizard.conf': Found

    [2018-05-23 16:13:32] ERROR[18311]: utils.c:1471 ast_careful_fwrite: fwrite() returned error: Broken pipe

    IPPBX*CLI> sip set debug ip 213.144.173.77
    No such command 'sip set debug ip 213.144.173.77' (type 'core show help sip set' for other possible commands)

    == Parsing '/etc/asterisk/pjsip.conf': Found

    == Parsing '/etc/asterisk/pjsip_auth.conf': Found

    == Parsing '/etc/asterisk/pjsip_wizard.conf': Found

    == Parsing '/etc/asterisk/pjsip.conf': Found
    == Parsing '/etc/asterisk/pjsip_auth.conf': Found

    == Parsing '/etc/asterisk/pjsip_wizard.conf': Found

    IPPBX*CLI> sip set debug 213.144.173.77
    No such command 'sip set debug 213.144.173.77' (type 'core show help sip set' for other possible commands)

    IPPBX*CLI> core show help sip set
    No such command 'sip set'.

    == Parsing '/etc/asterisk/pjsip.conf': Found

    == Parsing '/etc/asterisk/pjsip_auth.conf': Found

    == Parsing '/etc/asterisk/pjsip_wizard.conf': Found

    [2018-05-23 16:14:52] NOTICE[2114]: ysscale.c:1130 usb_exception_func: Total recv 2200 heartbeat packets from USB port 0

    IPPBX*CLI> IPPBX*CLI> sip set debug ip 213.144.173.77
    IPPBX*CLI> No such command 'sip set debug ip 213.144.173.77' (type 'core show he
    lp sip set' for other possible commands)
    No such command 'IPPBX*CLI> sip set debug ip 213.144.173.77' (type 'core show help IPPBX*CLI> sip' for other possible commands)
    No such command 'No such command 'sip set debug ip 213.144.173.77' (type 'core show help sip set' for other possible commands)' (type 'core show help No such' for other possible commands)

    == Parsing '/etc/asterisk/pjsip.conf': Found
    == Parsing '/etc/asterisk/pjsip_auth.conf': Found

    == Parsing '/etc/asterisk/pjsip_wizard.conf': Found

    IPPBX*CLI>

    - - - Updated - - -

    εχεις καποιο μαιλ να στο στειλω

Παρόμοια Θέματα

  1. ΟΤΕ Sip Trunk πρόβλημα με εισερχόμενες κλήσεις σε FreePBX
    Από Kapnos στο φόρουμ Voice over IP (VoIP) Software
    Μηνύματα: 1
    Τελευταίο Μήνυμα: 25-04-18, 14:26
  2. Πρόβλημα με κλήσεις
    Από atux_null στο φόρουμ Voice over IP (VoIP) Software
    Μηνύματα: 5
    Τελευταίο Μήνυμα: 28-02-18, 12:31
  3. Πρόβλημα με συνδεσιμοτητα στο dsl
    Από Στρατος1982romeo στο φόρουμ Nova
    Μηνύματα: 3
    Τελευταίο Μήνυμα: 03-12-17, 17:45
  4. Προβλημα(;) με τη γραμμη
    Από SciTeF στο φόρουμ COSMΟΤΕ
    Μηνύματα: 8
    Τελευταίο Μήνυμα: 25-05-17, 19:02
  5. Μηνύματα: 18
    Τελευταίο Μήνυμα: 20-05-17, 16:31

Bookmarks

Bookmarks

Δικαιώματα - Επιλογές

  • Δεν μπορείτε να δημοσιεύσετε νέα θέματα
  • Δεν μπορείτε να δημοσιεύσετε νέα μηνύματα
  • Δεν μπορείτε να αναρτήσετε συνημμένα
  • Δεν μπορείτε να επεξεργαστείτε τα μηνύματα σας
  •  
  • Τα BB code είναι σε λειτουργία
  • Τα Smilies είναι σε λειτουργία
  • Το [IMG] είναι σε λειτουργία
  • Το [VIDEO] είναι σε λειτουργία
  • Το HTML είναι εκτός λειτουργίας