Πρόταση Διανομής

**jim_p** · 12-12-19, 14:07

Μηπως απεγκατεστησες κατι που ειναι αναγκαιο για να κανει ασυρματες συνδεσεις, πχ χωρις το wpasupplicant δεν μπορεις να συνδεθεις σε οποιοδηποτε ασυρματο εχει wpa/wpa2 encryption.

**Subaru** · 12-12-19, 14:49

Ό,τι και να σου πω θα είναι ψέματα. Δεν έκανα κάτι από όσο ξέρω. Αν θυμάμαι καλά μετά από κάποιες ενημερώσεις που είχε κάνει πιο παλιά απέκτησε πρόβλημα. Θα δοκιμάσω να κάνω και εγκατάσταση το πακέτο που λες μπας και λείπει, αλλά δε νομίζω. Εγώ προσωπικά το μόνο που έκανα ήταν από την αρχή εγκατάσταση σε όλο το λειτουργικό. Αφού δεν δούλεψε όμως το network-manager πέρασα τα άλλα δύο που είπα (wicd και ceni) και τα αφαιρούσα όλα με την εντολή : apt-get --purge remove xxxx. Και μετά περνούσα το πακέτο που ήθελα με την εντολή apt-get install xxxx. Τώρα αν κατά την αφαίρεση πήραν και κάτι άλλο μαζί τους όπως αυτό που λες, δεν είδα κάτι παράξενο.

**pap** · 12-12-19, 15:10

Αρχικό μήνυμα από Subaru

Στο lsmod που μου είπες την δείχνει με τον ath5k που είπες. Εγώ δεν είπα πως δεν την βλέπω ή δεν βλέπω κάτι, αλλά ενώ βλέπει κανονικά όλα τα δίκτυα και μου τα εμφανίζει, μόλις πατήσω να συνδεθώ δε μου βγάζει καν παράθυρο για να βάλω κωδικό για το δίκτυο και με πετάει στην άλλη σύνδεση (ενσύρματη). Επίσης, αν ξετικάρω από το εικονίδιο πάνω στη μπάρα το enable wifi και το ξαναπατήσω να ανοίξει, τα δίκτυα έχουν πάει περίπατο. Πρέπει να κάνω επανεκκίνηση για να ξαναδώ δίκτυα.

απενεργοποίησε το ενσυρματο nic σου και άσε μονο το wifi.
αν πάλι δεν δεις αποτέλεσμα πόσταρε το output toy

Κώδικας:

ip addr

**Subaru** · 12-12-19, 21:05

Σκέτο wifi τζίφος η δουλειά ξανά. Η εντολή έχει το εξής output :

Κώδικας:

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether 00:14:0b:30:ab:94 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.3/24 brd 192.168.1.255 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 2a02:2149:8405:0:15b5:5479:b9e3:5bbc/64 scope global temporary dynamic 
       valid_lft 78177sec preferred_lft 34977sec
    inet6 2a02:2149:8405:0:214:bff:fe30:ab94/64 scope global dynamic 
       valid_lft 78177sec preferred_lft 34977sec
    inet6 fe80::214:bff:fe30:ab94/64 scope link 
       valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default qlen 1000
    link/ether 00:c0:a8:e5:83:d8 brd ff:ff:ff:ff:ff:ff

Ελπίζω να είναι σωστά....
Επίσης αν βάλω τώρα το βελάκι επάνω στο εικονίδιο του δικτύου μου λέει το εξής : Wifi is disabled by hardware switch. Ενώ το κουμπί που έχει το πατάω και δεν λειτουργεί. Τι να κάνω; Να το βραχυκυκλώσω για να μείνει ανοιχτό; Αν κάνω επανεκκίνηση βλέπω δίκτυα κανονικά, με το κουμπί στην ίδια κατάσταση. Ξαναλέω όμως, στο antix λειτουργούσε κανονικά το wifi και έβλεπα δίκτυα και συνδεόμουν.

**pap** · 12-12-19, 21:13

Περιμενε να δουμε τι γινεται.
sudo ip link set dev wlan0 up
και μετα ξαναποσταρε το
ip addr
EDIT
Δες και αυτο:
https://www.linuxbabe.com/ubuntu/connect-to-wi-fi-from-terminal-on-ubuntu-18-04-19-04-with-wpa-supplicant/amp

(Το σημειο με το rfkill μας ενδιαφερει)

**Subaru** · 13-12-19, 10:05

Μετά την εντολή και ip addr βγάζει πάλι το ίδιο :

Κώδικας:

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether 00:14:0b:30:ab:94 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.2/24 brd 192.168.1.255 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 2a02:2149:8405:0:9d5a:3ae5:e2d:fa40/64 scope global temporary dynamic 
       valid_lft 74495sec preferred_lft 31295sec
    inet6 2a02:2149:8405:0:214:bff:fe30:ab94/64 scope global dynamic 
       valid_lft 74495sec preferred_lft 31295sec
    inet6 fe80::214:bff:fe30:ab94/64 scope link 
       valid_lft forever preferred_lft forever
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
    link/ether 00:c0:a8:e5:83:d8 brd ff:ff:ff:ff:ff:ff

Την εντολή rfkill την έχω ξαναδοκιμάσει και η έξοδός της είναι :

Κώδικας:

0: phy0: Wireless LAN
	Soft blocked: no
	Hard blocked: no

Έκανα και την προσπάθεια της χειροκίνητης σύνδεσης και στις 4 προσπάθειες έχω αυτό :

Κώδικας:

Successfully initialized wpa_supplicant
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="WIND_KR" auth_failures=1 duration=10
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SSID-REENABLED id=0 ssid="WIND_KR"
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="WIND_KR" auth_failures=2 duration=20
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SSID-REENABLED id=0 ssid="WIND_KR"
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="WIND_KR" auth_failures=3 duration=20
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SSID-REENABLED id=0 ssid="WIND_KR"
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="WIND_KR" auth_failures=4 duration=20

**pap** · 13-12-19, 10:52

Αρχικό μήνυμα από Subaru

Μετά την εντολή και ip addr βγάζει πάλι το ίδιο :

Κώδικας:

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether 00:14:0b:30:ab:94 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.2/24 brd 192.168.1.255 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 2a02:2149:8405:0:9d5a:3ae5:e2d:fa40/64 scope global temporary dynamic 
       valid_lft 74495sec preferred_lft 31295sec
    inet6 2a02:2149:8405:0:214:bff:fe30:ab94/64 scope global dynamic 
       valid_lft 74495sec preferred_lft 31295sec
    inet6 fe80::214:bff:fe30:ab94/64 scope link 
       valid_lft forever preferred_lft forever
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
    link/ether 00:c0:a8:e5:83:d8 brd ff:ff:ff:ff:ff:ff

Την εντολή rfkill την έχω ξαναδοκιμάσει και η έξοδός της είναι :

Κώδικας:

0: phy0: Wireless LAN
	Soft blocked: no
	Hard blocked: no

Έκανα και την προσπάθεια της χειροκίνητης σύνδεσης και στις 4 προσπάθειες έχω αυτό :

Κώδικας:

Successfully initialized wpa_supplicant
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="WIND_KR" auth_failures=1 duration=10
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SSID-REENABLED id=0 ssid="WIND_KR"
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="WIND_KR" auth_failures=2 duration=20
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SSID-REENABLED id=0 ssid="WIND_KR"
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="WIND_KR" auth_failures=3 duration=20
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SCAN-STARTED 
wlan0: CTRL-EVENT-SSID-REENABLED id=0 ssid="WIND_KR"
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="WIND_KR" auth_failures=4 duration=20

η εντολή ήταν απλώς να "ανεβάσει" το ασύρματο interface σου, ~~το ότι δεν άλλαξε τίποτε δεν είναι καλό~~.

Κώδικας:

wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP>

μια χαρα ανέβηκε λάθος δικό μου
Απο κάτω όμως δείχνει ότι κάνει connect στο ασύρματο σου και το error που δίνει είναι ότι ο κωδικός που δίνεις είναι λάθος. (μπορείς με μια αναζήτηση στο internet να το διαπιστώσεις και μόνος σου)

**dimitri_ns** · 13-12-19, 11:08

Mπορεί να σε βοηθήσει
Για debugging βολεύει το dmesg

Οπότε δες τι σου βγάζει το antix kai ti soy bg;azei to xubuntu gia to wifi

**xaris2335** · 13-12-19, 11:54

Αρχικό μήνυμα από dimitri_ns

Mπορεί να σε βοηθήσει
Για debugging βολεύει το dmesg

Οπότε δες τι σου βγάζει το antix kai ti soy bg;azei to xubuntu gia to wifi

θα συμφωνήσω με αυτό + αναζήτηση μέσα για error, wlan, ath5k

Κώδικας:

sudo dmesg

https://www.howtogeek.com/449335/how...mand-on-linux/

**pap** · 13-12-19, 13:30

μπορείς να κάνεις debugging με πολούς τρόπους. Αντιλαμβάνεσαι τι γίνεται, κρίνοντας από τον διάλογο μέχρι τώρα, αν ακολούθησες τον οδηγό που σου έδωσα το link τότε μια καλή αρχή θα ήταν στην εντολή:

Κώδικας:

sudo wpa_supplicant -c /etc/wpa_supplicant.conf -i wlan0

να προσθέσεις το flag -d στο τέλος, για να δεις περισσότερες λεπτομέρειες για το error, αλλά και η πρόταση των παιδιών ποιο πάνω θα σε βοήθησει.

**Subaru** · 13-12-19, 15:20

Έδωσα την εντολή : sudo wpa_supplicant -c /etc/wpa_supplicant.conf -i wlan0 -d και πήρα την παρακάτω έξοδο, την οποία σταμάτησα σε κάποια στιγμή.

Κώδικας:

wpa_supplicant v2.1
random: Trying to read entropy from /dev/random
Successfully initialized wpa_supplicant
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
Priority group 0
   id=0 ssid='WIND_KR'
nl80211: Could not add multicast membership for vendor events: -2 (No such file or directory)
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Supported cipher 00-0f-ac:6
nl80211: Using driver-based off-channel TX
nl80211: interface wlan0 in phy phy0
nl80211: Set mode ifindex 3 iftype 2 (STATION)
nl80211: Subscribe to mgmt frames with non-AP handle 0x84bf8a8
nl80211: Register frame type=0xd0 nl_handle=0x84bf8a8 match=0104
nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=2): 01 04
nl80211: Register frame type=0xd0 nl_handle=0x84bf8a8 match=040a
nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=2): 04 0a
nl80211: Register frame type=0xd0 nl_handle=0x84bf8a8 match=040b
nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=2): 04 0b
nl80211: Register frame type=0xd0 nl_handle=0x84bf8a8 match=040c
nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=2): 04 0c
nl80211: Register frame type=0xd0 nl_handle=0x84bf8a8 match=040d
nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=2): 04 0d
nl80211: Register frame type=0xd0 nl_handle=0x84bf8a8 match=090a
nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=2): 09 0a
nl80211: Register frame type=0xd0 nl_handle=0x84bf8a8 match=090b
nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=2): 09 0b
nl80211: Register frame type=0xd0 nl_handle=0x84bf8a8 match=090c
nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=2): 09 0c
nl80211: Register frame type=0xd0 nl_handle=0x84bf8a8 match=090d
nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=2): 09 0d
nl80211: Register frame type=0xd0 nl_handle=0x84bf8a8 match=0409506f9a09
nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=6): 04 09 50 6f 9a 09
nl80211: Register frame type=0xd0 nl_handle=0x84bf8a8 match=7f506f9a09
nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=5): 7f 50 6f 9a 09
nl80211: Register frame type=0xd0 nl_handle=0x84bf8a8 match=0801
nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=2): 08 01
nl80211: Register frame type=0xd0 nl_handle=0x84bf8a8 match=06
nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=1): 06
nl80211: Register frame type=0xd0 nl_handle=0x84bf8a8 match=0a07
nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=2): 0a 07
nl80211: Register frame type=0xd0 nl_handle=0x84bf8a8 match=0a11
nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=2): 0a 11
nl80211: Failed to register Action frame processing - ignore for now
netlink: Operstate: ifindex=3 linkmode=1 (userspace-control), operstate=5 (IF_OPER_DORMANT)
nl80211: driver param='(null)'
Add interface wlan0 to a new radio phy0
nl80211: Regulatory information - country=AM
nl80211: 2402-2482 @ 40 MHz 20 mBm
nl80211: 5170-5250 @ 20 MHz 18 mBm
nl80211: 5250-5330 @ 20 MHz 18 mBm
nl80211: Added 802.11b mode based on 802.11g information
wlan0: Own MAC address: ******
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=4 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=5 set_tx=0 seq_len=0 key_len=0
wlan0: RSN: flushing PMKID list in the driver
nl80211: Flush PMKIDs
wlan0: Setting scan request: 0.100000 sec
wlan0: WPS: UUID based on MAC address: 971a2a19-09f3-512c-a85c-795a0020fca6
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
nl80211: Skip set_supp_port(unauthorized) while not associated
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
wlan0: Added interface wlan0
wlan0: State: DISCONNECTED -> DISCONNECTED
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
random: Got 20/20 bytes from /dev/random
wlan0: State: DISCONNECTED -> SCANNING
wlan0: Starting AP scan for wildcard SSID
wlan0: Add radio work 'scan'@0x84ce5d8
wlan0: First radio work item in the queue - schedule start immediately
wlan0: Starting radio work 'scan'@0x84ce5d8 after 0.000020 second wait
wlan0: nl80211: scan request
Scan requested (ret=0) - scan timeout 10 seconds
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan0
wlan0: nl80211: Scan trigger
wlan0: Event SCAN_STARTED (49) received
wlan0: Own scan request started a scan in 0.000045 seconds
wlan0: CTRL-EVENT-SCAN-STARTED 
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan0
wlan0: nl80211: New scan results available
nl80211: Scan probed for SSID ''
nl80211: Scan included frequencies: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 2472
wlan0: Event SCAN_RESULTS (3) received
wlan0: Scan completed in 0.779076 seconds
nl80211: Received scan results (5 BSSes)
wlan0: BSS: Start scan result update 1
wlan0: BSS: Add new id 0 BSSID ****** SSID 'WIND_KR'
wlan0: BSS: Add new id 1 BSSID 34:4d:ea:85:96:04 SSID 'HOL_ZTE_4'
wlan0: BSS: Add new id 2 BSSID ****** SSID 'Wind_KR_ext'
wlan0: BSS: Add new id 3 BSSID a4:91:b1:66:9f:77 SSID 'Tsirbas'
wlan0: BSS: Add new id 4 BSSID cc:7b:35:17:e0:b0 SSID 'CYTAE0B0'
BSS: last_scan_res_used=5/32
wlan0: New scan results available (own=1 ext=0)
WPS: AP ****** type 0 added
WPS: AP 34:4d:ea:85:96:04 type 0 added
WPS: AP ****** type 0 added
WPS: AP a4:91:b1:66:9f:77 type 0 added
WPS: AP cc:7b:35:17:e0:b0 type 0 added
WPS: AP[0] ****** type=0 tries=0 last_attempt=-1 sec ago blacklist=0
WPS: AP[1] 34:4d:ea:85:96:04 type=0 tries=0 last_attempt=-1 sec ago blacklist=0
WPS: AP[2] ****** type=0 tries=0 last_attempt=-1 sec ago blacklist=0
WPS: AP[3] a4:91:b1:66:9f:77 type=0 tries=0 last_attempt=-1 sec ago blacklist=0
WPS: AP[4] cc:7b:35:17:e0:b0 type=0 tries=0 last_attempt=-1 sec ago blacklist=0
wlan0: Radio work 'scan'@0x84ce5d8 done in 0.779908 seconds
wlan0: Selecting BSS from priority group 0
wlan0: 0: ****** ssid='WIND_KR' wpa_ie_len=0 rsn_ie_len=24 caps=0x411 level=-41 wps
wlan0:    selected based on RSN IE
wlan0:    selected BSS ****** ssid='WIND_KR'
wlan0: Considering connect request: reassociate: 0  selected: ******  bssid: 00:00:00:00:00:00  pending: 00:00:00:00:00:00  wpa_state: SCANNING  ssid=0x84bf218  current_ssid=(nil)
wlan0: Request association with ******
wlan0: Add radio work 'sme-connect'@0x84ce5d8
wlan0: First radio work item in the queue - schedule start immediately
wlan0: Starting radio work 'sme-connect'@0x84ce5d8 after 0.000036 second wait
wlan0: Automatic auth_alg selection: 0x1
RSN: PMKSA cache search - network_ctx=(nil) try_opportunistic=0
RSN: Search for BSSID ******
RSN: No PMKSA cache entry found
wlan0: RSN: using IEEE 802.11i/D9.0
wlan0: WPA: Selected cipher suites: group 8 pairwise 24 key_mgmt 2 proto 2
wlan0: WPA: Selected mgmt group cipher 32
wlan0: WPA: clearing AP WPA IE
WPA: set AP RSN IE - hexdump(len=26): 30 18 01 00 00 0f ac 02 02 00 00 0f ac 02 00 0f ac 04 01 00 00 0f ac 02 00 00
wlan0: WPA: using GTK TKIP
wlan0: WPA: using PTK CCMP
wlan0: WPA: using KEY_MGMT WPA-PSK
wlan0: WPA: not using MGMT group cipher
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
FT: Stored MDIE and FTIE from (Re)Association Response - hexdump(len=0):
wlan0: Cancelling scan request
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: State: SCANNING -> AUTHENTICATING
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
nl80211: Authenticate (ifindex=3)
  * bssid=******
  * freq=2452
  * SSID - hexdump_ascii(len=7):
     57 49 4e 44 5f 4b 52                              WIND_KR         
  * IEs - hexdump(len=0): [NULL]
  * Auth Type 0
nl80211: Authentication request send successfully
nl80211: Drv Event 19 (NL80211_CMD_NEW_STATION) received for wlan0
nl80211: New station ******
RTM_NEWLINK: ifi_index=3 ifname=wlan0 wext ifi_flags=0x1003 ([UP])
EAPOL: disable timer tick
nl80211: Drv Event 20 (NL80211_CMD_DEL_STATION) received for wlan0
nl80211: Delete station ******
nl80211: Drv Event 37 (NL80211_CMD_AUTHENTICATE) received for wlan0
nl80211: MLME event 37; timeout with ******
wlan0: Event AUTH_TIMED_OUT (14) received
wlan0: SME: Authentication timed out
wlan0: Radio work 'sme-connect'@0x84ce5d8 done in 0.630293 seconds
Added BSSID ****** into blacklist
wlan0: Blacklist count 1 --> request scan in 100 ms
wlan0: Setting scan request: 0.100000 sec
wlan0: State: AUTHENTICATING -> DISCONNECTED
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
wlan0: State: DISCONNECTED -> SCANNING
wlan0: Starting AP scan for wildcard SSID
wlan0: Add radio work 'scan'@0x84cecc0
wlan0: First radio work item in the queue - schedule start immediately
wlan0: Starting radio work 'scan'@0x84cecc0 after 0.000036 second wait
wlan0: nl80211: scan request
Scan requested (ret=0) - scan timeout 30 seconds
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan0
wlan0: nl80211: Scan trigger
wlan0: Event SCAN_STARTED (49) received
wlan0: Own scan request started a scan in 0.000040 seconds
wlan0: CTRL-EVENT-SCAN-STARTED 
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan0
wlan0: nl80211: New scan results available
nl80211: Scan probed for SSID ''
nl80211: Scan included frequencies: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 2472
wlan0: Event SCAN_RESULTS (3) received
wlan0: Scan completed in 0.779716 seconds
nl80211: Received scan results (5 BSSes)
wlan0: BSS: Start scan result update 2
BSS: last_scan_res_used=5/32
wlan0: New scan results available (own=1 ext=0)
WPS: AP[0] ****** type=0 tries=0 last_attempt=-1 sec ago blacklist=1
WPS: AP[1] 34:4d:ea:85:96:04 type=0 tries=0 last_attempt=-1 sec ago blacklist=0
WPS: AP[2] ****** type=0 tries=0 last_attempt=-1 sec ago blacklist=0
WPS: AP[3] a4:91:b1:66:9f:77 type=0 tries=0 last_attempt=-1 sec ago blacklist=0
WPS: AP[4] cc:7b:35:17:e0:b0 type=0 tries=0 last_attempt=-1 sec ago blacklist=0
wlan0: Radio work 'scan'@0x84cecc0 done in 0.780601 seconds
wlan0: Selecting BSS from priority group 0
wlan0: 0: ****** ssid='WIND_KR' wpa_ie_len=0 rsn_ie_len=24 caps=0x411 level=-39 wps
wlan0:    skip - blacklisted (count=1 limit=0)
wlan0: 1: 34:4d:ea:85:96:04 ssid='HOL_ZTE_4' wpa_ie_len=26 rsn_ie_len=24 caps=0x411 level=-69 wps
wlan0:    skip - SSID mismatch
wlan0: 2: ****** ssid='Wind_KR_ext' wpa_ie_len=0 rsn_ie_len=24 caps=0x31 level=-73 wps
wlan0:    skip - SSID mismatch
wlan0: 3: a4:91:b1:66:9f:77 ssid='Tsirbas' wpa_ie_len=0 rsn_ie_len=20 caps=0x1411 level=-76 wps
wlan0:    skip - SSID mismatch
wlan0: 4: cc:7b:35:17:e0:b0 ssid='CYTAE0B0' wpa_ie_len=26 rsn_ie_len=24 caps=0x431 level=-88 wps
wlan0:    skip - SSID mismatch
wlan0: No APs found - clear blacklist and try again
Removed BSSID ****** from blacklist (clear)
wlan0: Selecting BSS from priority group 0
wlan0: 0: ****** ssid='WIND_KR' wpa_ie_len=0 rsn_ie_len=24 caps=0x411 level=-39 wps
wlan0:    selected based on RSN IE
wlan0:    selected BSS ****** ssid='WIND_KR'
wlan0: Considering connect request: reassociate: 0  selected: ******  bssid: 00:00:00:00:00:00  pending: 00:00:00:00:00:00  wpa_state: SCANNING  ssid=0x84bf218  current_ssid=(nil)
wlan0: Request association with ******
wlan0: Add radio work 'sme-connect'@0x84cecc0
wlan0: First radio work item in the queue - schedule start immediately
RSN: Ignored PMKID candidate without preauth flag
wlan0: Starting radio work 'sme-connect'@0x84cecc0 after 0.000040 second wait
wlan0: Automatic auth_alg selection: 0x1
RSN: PMKSA cache search - network_ctx=(nil) try_opportunistic=0
RSN: Search for BSSID ******
RSN: No PMKSA cache entry found
wlan0: RSN: using IEEE 802.11i/D9.0
wlan0: WPA: Selected cipher suites: group 8 pairwise 24 key_mgmt 2 proto 2
wlan0: WPA: Selected mgmt group cipher 32
wlan0: WPA: clearing AP WPA IE
WPA: set AP RSN IE - hexdump(len=26): 30 18 01 00 00 0f ac 02 02 00 00 0f ac 02 00 0f ac 04 01 00 00 0f ac 02 00 00
wlan0: WPA: using GTK TKIP
wlan0: WPA: using PTK CCMP
wlan0: WPA: using KEY_MGMT WPA-PSK
wlan0: WPA: not using MGMT group cipher
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
FT: Stored MDIE and FTIE from (Re)Association Response - hexdump(len=0):
wlan0: Cancelling scan request
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: State: SCANNING -> AUTHENTICATING
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
nl80211: Authenticate (ifindex=3)
  * bssid=******
  * freq=2452
  * SSID - hexdump_ascii(len=7):
     57 49 4e 44 5f 4b 52                              WIND_KR         
  * IEs - hexdump(len=0): [NULL]
  * Auth Type 0
nl80211: Authentication request send successfully
RTM_NEWLINK: ifi_index=3 ifname=wlan0 wext ifi_flags=0x1003 ([UP])
nl80211: Drv Event 19 (NL80211_CMD_NEW_STATION) received for wlan0
nl80211: New station ******
nl80211: Drv Event 20 (NL80211_CMD_DEL_STATION) received for wlan0
nl80211: Delete station ******
nl80211: Drv Event 37 (NL80211_CMD_AUTHENTICATE) received for wlan0
nl80211: MLME event 37; timeout with ******
wlan0: Event AUTH_TIMED_OUT (14) received
wlan0: SME: Authentication timed out
wlan0: Radio work 'sme-connect'@0x84cecc0 done in 0.629608 seconds
Added BSSID ****** into blacklist
wlan0: Blacklist count 2 --> request scan in 500 ms
wlan0: Setting scan request: 0.500000 sec
wlan0: State: AUTHENTICATING -> DISCONNECTED
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
wlan0: State: DISCONNECTED -> SCANNING
wlan0: Starting AP scan for wildcard SSID
wlan0: Add radio work 'scan'@0x84ced10
wlan0: First radio work item in the queue - schedule start immediately
wlan0: Starting radio work 'scan'@0x84ced10 after 0.000025 second wait
wlan0: nl80211: scan request
Scan requested (ret=0) - scan timeout 30 seconds
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan0
wlan0: nl80211: Scan trigger
wlan0: Event SCAN_STARTED (49) received
wlan0: Own scan request started a scan in 0.000060 seconds
wlan0: CTRL-EVENT-SCAN-STARTED 
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan0
wlan0: nl80211: New scan results available
nl80211: Scan probed for SSID ''
nl80211: Scan included frequencies: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 2472
wlan0: Event SCAN_RESULTS (3) received
wlan0: Scan completed in 0.780674 seconds
nl80211: Received scan results (5 BSSes)
wlan0: BSS: Start scan result update 3
BSS: last_scan_res_used=5/32
wlan0: New scan results available (own=1 ext=0)
WPS: AP[0] ****** type=0 tries=0 last_attempt=-1 sec ago blacklist=1
WPS: AP[1] 34:4d:ea:85:96:04 type=0 tries=0 last_attempt=-1 sec ago blacklist=0
WPS: AP[2] ****** type=0 tries=0 last_attempt=-1 sec ago blacklist=0
WPS: AP[3] a4:91:b1:66:9f:77 type=0 tries=0 last_attempt=-1 sec ago blacklist=0
WPS: AP[4] cc:7b:35:17:e0:b0 type=0 tries=0 last_attempt=-1 sec ago blacklist=0
wlan0: Radio work 'scan'@0x84ced10 done in 0.781336 seconds
wlan0: Selecting BSS from priority group 0
wlan0: 0: ****** ssid='WIND_KR' wpa_ie_len=0 rsn_ie_len=24 caps=0x411 level=-40 wps
wlan0:    skip - blacklisted (count=1 limit=0)
wlan0: 1: 34:4d:ea:85:96:04 ssid='HOL_ZTE_4' wpa_ie_len=26 rsn_ie_len=24 caps=0x411 level=-68 wps
wlan0:    skip - SSID mismatch
wlan0: 2: ****** ssid='Wind_KR_ext' wpa_ie_len=0 rsn_ie_len=24 caps=0x31 level=-76 wps
wlan0:    skip - SSID mismatch
wlan0: 3: a4:91:b1:66:9f:77 ssid='Tsirbas' wpa_ie_len=0 rsn_ie_len=20 caps=0x1411 level=-76 wps
wlan0:    skip - SSID mismatch
wlan0: 4: cc:7b:35:17:e0:b0 ssid='CYTAE0B0' wpa_ie_len=26 rsn_ie_len=24 caps=0x431 level=-84 wps
wlan0:    skip - SSID mismatch
wlan0: No APs found - clear blacklist and try again
Removed BSSID ****** from blacklist (clear)
wlan0: Selecting BSS from priority group 0
wlan0: 0: ****** ssid='WIND_KR' wpa_ie_len=0 rsn_ie_len=24 caps=0x411 level=-40 wps
wlan0:    selected based on RSN IE
wlan0:    selected BSS ****** ssid='WIND_KR'
wlan0: Considering connect request: reassociate: 0  selected: ******  bssid: 00:00:00:00:00:00  pending: 00:00:00:00:00:00  wpa_state: SCANNING  ssid=0x84bf218  current_ssid=(nil)
wlan0: Request association with ******
wlan0: Add radio work 'sme-connect'@0x84cec18
wlan0: First radio work item in the queue - schedule start immediately
RSN: Ignored PMKID candidate without preauth flag
wlan0: Starting radio work 'sme-connect'@0x84cec18 after 0.000039 second wait
wlan0: Automatic auth_alg selection: 0x1
RSN: PMKSA cache search - network_ctx=(nil) try_opportunistic=0
RSN: Search for BSSID ******
RSN: No PMKSA cache entry found
wlan0: RSN: using IEEE 802.11i/D9.0
wlan0: WPA: Selected cipher suites: group 8 pairwise 24 key_mgmt 2 proto 2
wlan0: WPA: Selected mgmt group cipher 32
wlan0: WPA: clearing AP WPA IE
WPA: set AP RSN IE - hexdump(len=26): 30 18 01 00 00 0f ac 02 02 00 00 0f ac 02 00 0f ac 04 01 00 00 0f ac 02 00 00
wlan0: WPA: using GTK TKIP
wlan0: WPA: using PTK CCMP
wlan0: WPA: using KEY_MGMT WPA-PSK
wlan0: WPA: not using MGMT group cipher
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
FT: Stored MDIE and FTIE from (Re)Association Response - hexdump(len=0):
wlan0: Cancelling scan request
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: State: SCANNING -> AUTHENTICATING
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
nl80211: Authenticate (ifindex=3)
  * bssid=******
  * freq=2452
  * SSID - hexdump_ascii(len=7):
     57 49 4e 44 5f 4b 52                              WIND_KR         
  * IEs - hexdump(len=0): [NULL]
  * Auth Type 0
nl80211: Authentication request send successfully
nl80211: Drv Event 19 (NL80211_CMD_NEW_STATION) received for wlan0
nl80211: New station ******
RTM_NEWLINK: ifi_index=3 ifname=wlan0 wext ifi_flags=0x1003 ([UP])
nl80211: Drv Event 20 (NL80211_CMD_DEL_STATION) received for wlan0
nl80211: Delete station ******
nl80211: Drv Event 37 (NL80211_CMD_AUTHENTICATE) received for wlan0
nl80211: MLME event 37; timeout with ******
wlan0: Event AUTH_TIMED_OUT (14) received
wlan0: SME: Authentication timed out
wlan0: Radio work 'sme-connect'@0x84cec18 done in 0.640237 seconds
Added BSSID ****** into blacklist
wlan0: Blacklist count 3 --> request scan in 1000 ms
wlan0: Setting scan request: 1.000000 sec
wlan0: State: AUTHENTICATING -> DISCONNECTED
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
wlan0: State: DISCONNECTED -> SCANNING
wlan0: Starting AP scan for wildcard SSID
wlan0: Add radio work 'scan'@0x84cecc0
wlan0: First radio work item in the queue - schedule start immediately
wlan0: Starting radio work 'scan'@0x84cecc0 after 0.000026 second wait
wlan0: nl80211: scan request
Scan requested (ret=0) - scan timeout 30 seconds
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan0
wlan0: nl80211: Scan trigger
wlan0: Event SCAN_STARTED (49) received
wlan0: Own scan request started a scan in 0.000060 seconds
wlan0: CTRL-EVENT-SCAN-STARTED 
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan0
wlan0: nl80211: New scan results available
nl80211: Scan probed for SSID ''
nl80211: Scan included frequencies: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 2472
wlan0: Event SCAN_RESULTS (3) received
wlan0: Scan completed in 0.777560 seconds
nl80211: Received scan results (5 BSSes)
wlan0: BSS: Start scan result update 4
BSS: last_scan_res_used=5/32
wlan0: New scan results available (own=1 ext=0)
WPS: AP[0] ****** type=0 tries=0 last_attempt=-1 sec ago blacklist=1
WPS: AP[1] 34:4d:ea:85:96:04 type=0 tries=0 last_attempt=-1 sec ago blacklist=0
WPS: AP[2] ****** type=0 tries=0 last_attempt=-1 sec ago blacklist=0
WPS: AP[3] a4:91:b1:66:9f:77 type=0 tries=0 last_attempt=-1 sec ago blacklist=0
WPS: AP[4] cc:7b:35:17:e0:b0 type=0 tries=0 last_attempt=-1 sec ago blacklist=0
wlan0: Radio work 'scan'@0x84cecc0 done in 0.778215 seconds
wlan0: Selecting BSS from priority group 0
wlan0: 0: ****** ssid='WIND_KR' wpa_ie_len=0 rsn_ie_len=24 caps=0x411 level=-39 wps
wlan0:    skip - blacklisted (count=1 limit=0)
wlan0: 1: 34:4d:ea:85:96:04 ssid='HOL_ZTE_4' wpa_ie_len=26 rsn_ie_len=24 caps=0x411 level=-71 wps
wlan0:    skip - SSID mismatch
wlan0: 2: ****** ssid='Wind_KR_ext' wpa_ie_len=0 rsn_ie_len=24 caps=0x31 level=-72 wps
wlan0:    skip - SSID mismatch
wlan0: 3: a4:91:b1:66:9f:77 ssid='Tsirbas' wpa_ie_len=0 rsn_ie_len=20 caps=0x1411 level=-76 wps
wlan0:    skip - SSID mismatch
wlan0: 4: cc:7b:35:17:e0:b0 ssid='CYTAE0B0' wpa_ie_len=26 rsn_ie_len=24 caps=0x431 level=-84 wps
wlan0:    skip - SSID mismatch
wlan0: No APs found - clear blacklist and try again
Removed BSSID ****** from blacklist (clear)
wlan0: Selecting BSS from priority group 0
wlan0: 0: ****** ssid='WIND_KR' wpa_ie_len=0 rsn_ie_len=24 caps=0x411 level=-39 wps
wlan0:    selected based on RSN IE
wlan0:    selected BSS ****** ssid='WIND_KR'
wlan0: Considering connect request: reassociate: 0  selected: ******  bssid: 00:00:00:00:00:00  pending: 00:00:00:00:00:00  wpa_state: SCANNING  ssid=0x84bf218  current_ssid=(nil)
wlan0: Request association with ******
wlan0: Add radio work 'sme-connect'@0x84cecc0
wlan0: First radio work item in the queue - schedule start immediately
RSN: Ignored PMKID candidate without preauth flag
wlan0: Starting radio work 'sme-connect'@0x84cecc0 after 0.000041 second wait
wlan0: Automatic auth_alg selection: 0x1
RSN: PMKSA cache search - network_ctx=(nil) try_opportunistic=0
RSN: Search for BSSID ******
RSN: No PMKSA cache entry found
wlan0: RSN: using IEEE 802.11i/D9.0
wlan0: WPA: Selected cipher suites: group 8 pairwise 24 key_mgmt 2 proto 2
wlan0: WPA: Selected mgmt group cipher 32
wlan0: WPA: clearing AP WPA IE
WPA: set AP RSN IE - hexdump(len=26): 30 18 01 00 00 0f ac 02 02 00 00 0f ac 02 00 0f ac 04 01 00 00 0f ac 02 00 00
wlan0: WPA: using GTK TKIP
wlan0: WPA: using PTK CCMP
wlan0: WPA: using KEY_MGMT WPA-PSK
wlan0: WPA: not using MGMT group cipher
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
FT: Stored MDIE and FTIE from (Re)Association Response - hexdump(len=0):
wlan0: Cancelling scan request
wlan0: SME: Trying to authenticate with ****** (SSID='WIND_KR' freq=2452 MHz)
wlan0: State: SCANNING -> AUTHENTICATING
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
nl80211: Authenticate (ifindex=3)
  * bssid=******
  * freq=2452
  * SSID - hexdump_ascii(len=7):
     57 49 4e 44 5f 4b 52                              WIND_KR         
  * IEs - hexdump(len=0): [NULL]
  * Auth Type 0
nl80211: Authentication request send successfully
nl80211: Drv Event 19 (NL80211_CMD_NEW_STATION) received for wlan0
nl80211: New station ******
RTM_NEWLINK: ifi_index=3 ifname=wlan0 wext ifi_flags=0x1003 ([UP])
nl80211: Drv Event 20 (NL80211_CMD_DEL_STATION) received for wlan0
nl80211: Delete station ******
nl80211: Drv Event 37 (NL80211_CMD_AUTHENTICATE) received for wlan0
nl80211: MLME event 37; timeout with ******
wlan0: Event AUTH_TIMED_OUT (14) received
wlan0: SME: Authentication timed out
wlan0: Radio work 'sme-connect'@0x84cecc0 done in 0.629963 seconds
Added BSSID c:39:53:b2:73:cc into blacklist
Continuous association failures - consider temporary network disabling
wlan0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="WIND_KR" auth_failures=1 duration=10
wlan0: Blacklist count 4 --> request scan in 5000 ms
wlan0: Setting scan request: 5.000000 sec
wlan0: State: AUTHENTICATING -> DISCONNECTED
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
^Cwlan0: Removing interface wlan0
wlan0: Request to deauthenticate - bssid=00:00:00:00:00:00 pending_bssid=00:00:00:00:00:00 reason=3 state=DISCONNECTED
wlan0: State: DISCONNECTED -> DISCONNECTED
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Removed BSSID ****** from blacklist (clear)
wlan0: BSS: Remove id 0 BSSID ****** SSID 'WIND_KR' due to wpa_bss_flush
wlan0: BSS: Remove id 1 BSSID 34:4d:ea:85:96:04 SSID 'HOL_ZTE_4' due to wpa_bss_flush
wlan0: BSS: Remove id 2 BSSID ****** SSID 'Wind_KR_ext' due to wpa_bss_flush
wlan0: BSS: Remove id 3 BSSID a4:91:b1:66:9f:77 SSID 'Tsirbas' due to wpa_bss_flush
wlan0: BSS: Remove id 4 BSSID cc:7b:35:17:e0:b0 SSID 'CYTAE0B0' due to wpa_bss_flush
wlan0: Cancelling scan request
wlan0: Cancelling authentication timeout
Remove interface wlan0 from radio phy0
Remove radio phy0
nl80211: Remove monitor interface: refcount=0
netlink: Operstate: ifindex=3 linkmode=0 (kernel-control), operstate=6 (IF_OPER_UP)
nl80211: Set mode ifindex 3 iftype 2 (STATION)
nl80211: Unsubscribe mgmt frames handle 0x80c37021 (mode change)
wlan0: CTRL-EVENT-TERMINATING

Το dmesg για το wlan έδωσε :

Κώδικας:

[   27.411379] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   27.413316] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   27.829071] audit_printk_skb: 39 callbacks suppressed
[   27.829080] type=1400 audit(1576237955.621:25): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cups-browsed" pid=961 comm="apparmor_parser"
[   30.287240] init: plymouth-upstart-bridge main process ended, respawning
[   30.305406] init: plymouth-upstart-bridge main process ended, respawning
[   51.781771] wlan0: authenticate with ******
[   51.792380] wlan0: direct probe to ****** (try 1/3)
[   51.996082] wlan0: direct probe to ****** (try 2/3)
[   52.200086] wlan0: direct probe to ****** (try 3/3)
[   52.404072] wlan0: authentication with ****** timed out
[   55.940332] type=1400 audit(1576237995.266:26): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=2041 comm="apparmor_parser"
[   55.940359] type=1400 audit(1576237995.266:27): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2041 comm="apparmor_parser"
[   59.096677] wlan0: authenticate with ******
[   59.100944] wlan0: direct probe to ****** (try 1/3)
[   59.304053] wlan0: direct probe to ****** (try 2/3)
[   59.508055] wlan0: direct probe to ****** (try 3/3)
[   59.712062] wlan0: authentication with ****** timed out
[   61.012763] wlan0: authenticate with ******
[   61.016769] wlan0: direct probe to ****** (try 1/3)
[   61.220055] wlan0: direct probe to ****** (try 2/3)
[   61.424043] wlan0: direct probe to ****** (try 3/3)
[   61.628055] wlan0: authentication with ****** timed out
[   63.186207] systemd-hostnamed[2062]: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolveable. Please install nss-myhostname!
[   63.421829] wlan0: authenticate with ******
[   63.426064] wlan0: direct probe to ****** (try 1/3)
[   63.628077] wlan0: direct probe to ****** (try 2/3)
[   63.832070] wlan0: direct probe to ****** (try 3/3)
[   64.036042] wlan0: authentication with ****** timed out
[   75.613856] wlan0: authenticate with ******
[   75.618247] wlan0: direct probe to ****** (try 1/3)
[   75.820043] wlan0: direct probe to ****** (try 2/3)
[   76.024045] wlan0: direct probe to ****** (try 3/3)
[   76.228039] wlan0: authentication with ****** timed out
[   85.453801] wlan0: authenticate with ******
[   85.454071] wlan0: direct probe to  (try 1/3)
[   85.656045] wlan0: direct probe to  (try 2/3)
[   85.860044] wlan0: direct probe to  (try 3/3)
[   86.064045] wlan0: authentication with  timed out
[   96.870444] wlan0: authenticate with 
[   96.880323] wlan0: direct probe to  (try 1/3)
[   97.084122] wlan0: direct probe to  (try 2/3)
[   97.288100] wlan0: direct probe to  (try 3/3)
[   97.492126] wlan0: authentication with ****** timed out
[  119.703529] perf samples too long (2567 > 2500), lowering kernel.perf_event_max_sample_rate to 50000
[  289.370919] perf samples too long (5080 > 5000), lowering kernel.perf_event_max_sample_rate to 25000
[  332.813471] wlan0: authenticate with ******
[  332.818011] wlan0: direct probe to ****** (try 1/3)
[  333.020097] wlan0: direct probe to ****** (try 2/3)
[  333.224082] wlan0: direct probe to ****** (try 3/3)
[  333.428082] wlan0: authentication with ****** timed out
[  334.325393] wlan0: authenticate with ******
[  334.330399] wlan0: direct probe to ****** (try 1/3)
[  334.532102] wlan0: direct probe to ****** (try 2/3)
[  334.736114] wlan0: direct probe to ****** (try 3/3)
[  334.940088] wlan0: authentication with ****** timed out
[  336.237324] wlan0: authenticate with ******
[  336.241792] wlan0: direct probe to ****** (try 1/3)
[  336.444094] wlan0: direct probe to ****** (try 2/3)
[  336.648082] wlan0: direct probe to ****** (try 3/3)
[  336.852078] wlan0: authentication with ****** timed out
[  338.657397] wlan0: authenticate with ******
[  338.661619] wlan0: direct probe to ****** (try 1/3)
[  338.864089] wlan0: direct probe to ****** (try 2/3)
[  339.068089] wlan0: direct probe to ****** (try 3/3)
[  339.272076] wlan0: authentication with ****** timed out

**pap** · 13-12-19, 15:56

κοίτα το θέμα είναι ότι η κάρτα σου δουλεύει, τώρα μπορεί να είναι πολλοί οι λόγοι που δεν γίνεται το authentication, γιατί αύτο είναι το πρόβλημα το οποίο προκαλεί το time out, μπορείς να βρεις αρκετά πράγματα στο internet αν δεν έχεις ήδη βαρεθεί, κάπου διάβασα ότι ίσως πρέπει να σταματήσεις τον network manager όταν τρέχεις την εντολή (αλήθεια μέσω network manager εξακολουθεί να μην γίνεται τίποτε

, εμένα η τελευταία μου ελπίδα είναι να προσθέσεις το flag -D wext.
Υ.Γ
δεν έχεις κρυφό το ssid στον router σου ε;

**Subaru** · 15-12-19, 20:20

Όχι δεν έχω κρυφό το ssid μου στον router. Στις υπόλοιπες συσκευές του σπιτιού συνδέομαι κανονικά. Απλά, ένα λαμπάκι που άναβε με το wifi πλέον δεν ανάβει και υποψιάζομαι πως είναι η πλακετούλα που είναι το κουμπί επάνω που μου κάνει το πρόβλημα. Έχω πλέον το Network manager και όλες οι εντολές που έδωσα είναι με το network manager εγκατεστημένο. Τον κωδικό τον έχω περάσει πάνω από 50 φορές μέχρι τώρα, αλλά δε νομίζω να είναι αυτό το πρόβλημα. Το κόβω μάλλον για hardware και δε με βλέπω να πολυασχολούμαι κιόλας. Τα Laptop είναι πάνω από 15 χρόνια και απλά είπα να το επισκευάσω να κάνω λίγο πιο εύκολη τη ζωή του πατέρα μου! Σας ευχαριστώ για το χρόνο σας και τη βοήθεια σας! Καλή συνέχεια σε όλους και καλές γιορτές!! Το θέμα μπορεί να κλειδωθεί από τους διαχειριστές. Σας ευχαριστώ και πάλι!!

Θέμα: Πρόταση Διανομής

Bookmarks

Bookmarks

Δικαιώματα - Επιλογές