CPU: 3 PID: 331 Comm: ethphxcmd Tainted: P O 3.18.21 #1
task: 8a17a6b8 ti: 8a22c000 task.ti: 8a22c000
$ 0 : 00000000 00000008 00000000 00000000
$ 4 : 00000000 00000000 00000000 00000000
$ 8 : 00000000 00000000 00000000 00000000
$12 : 00000000 77ace450 00000000 00000000
$16 : 00000000 8a22fda8 8a22fda8 00000000
$20 : ffffffff 00480000 00486437 00adb83c
$24 : 00000000 8021adf4
$28 : 8a22c000 8a22fd78 7fcd0230 802e48dc
Hi : 00000369
Lo : 00001be5
epc : 00000000 (null)
Tainted: P O
ra : 802e48dc generic_mii_ioctl+0x8c/0x158
Status: 11000003 KERNEL EXL IE
Cause : 5080d008
BadVA : 00000000
PrId : 0001992f (MIPS 1004Kc)
Modules linked in: hw_nat(PO) ebt_policer ebt_ip6 ebt_ip ebtable_filter ebtable_broute ebtables sch_prio sch_htb cls_fw act_mirred mapfilter(O) mt7615_ap(O) tc3162_dmt(PO) qdma_wan(PO) eth_ephy(PO) eth(PO) qdma_lan(PO) fe_core(PO) crypto_k(PO) sif(PO) detectprtype(PO) tccicmd(PO) tcledctrl(PO) speedtest(PO) tcvlantag(O) tcportbind(O) tcs
BGA IC
Xtal:1
DDR3 init.
DRAMC init done.
Calculate size.
DRAM size=256MB
Set new TRFC.
ddr-1333
7516DRAMC V1.0 (0)
Press 'x' or 'b' key in 1 secs to enter or skip bootloader upgrade.
EN751627 at Fri Nov 19 18:51:49 CST 2021 version 1.1 free bootbase
Set SPI Clock to 50 Mhz
spi_nand_probe: mfr_id=0xef, dev_id=0xaa, dev_id2=0x21
Using Flash ECC.
Detected SPI NAND Flash : _SPI_NAND_DEVICE_ID_W25N01G, Flash Size=0x8000000
bmt pool size: 81
BMT & BBT Init Success
The MAC address in flash is null!
ZyXEL zloader v1.4.7 (11/19/2021 - 18:51:46)
Multiboot client version: 2.5
Not found TC Phy
Not found TC Phy
Not found TC Phy
Not found TC Phy
Not found TC Phy
GE Rext AnaCal Done! (5)(0x1b)
Hit any key to stop autoboot: 0
==> boot flag = 0
main tclinux.bin have ZYXEL trx header!
from main
Decompress to 80002000 free_mem_ptr=81100000 free_mem_ptr_end=80780000
Uncompressing [LZMA] ... done.
ECNT ring buffer init success
mknod: /dev/ppp: File exists
mknod: /dev/ptmx: File exists
mknod: /dev/ptyp0: File exists
mknod: /dev/ptyp1: File exists
mknod: /dev/ptyp2: File exists
mknod: /dev/ttyp0: File exists
mknod: /dev/ttyp1: File exists
mknod: /dev/ttyp2: File exists
mknod: /dev/watchdog: File exists
mknod: /dev/ttyS20: File exists
mknod: /dev/ttyS30: File exists
mknod: /dev/hwnat0: File exists
mknod: /dev/acl0: File exists
mknod: /dev/ac0: File exists
mknod: /dev/mtr0: File exists
**************prepare var*****************
busybox init and set aff
init started: BusyBox v1.20.1 (2023-12-13 14:54:16 CST)
chmod: /userfs/profile.cfg: Read-only file system
TCSUPPORT_IPV6
Reading MT7615 5G EEPROM from flash reservearea
mtd[readflash]:device=reservearea tclen=1024 tcoffset=131072
Unlocking reservearea ...
Reading from reservearea to /etc/Wireless/RT2860AP_AC/RT30xxEEPROM.bin ...
Reading MT7615 5G CALDATA from flash reservearea
mtd[readflash]:device=reservearea tclen=36864 tcoffset=135168
Unlocking reservearea ...
Reading from reservearea to /etc/Wireless/RT2860AP_AC/CALDATA_default.bin ...
hexdump: /etc/RT30xxEEPROM.bin: No such file or directory
insmod ETH_LAN driver
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
ifconfig: SIOCSIFFLAGS: Cannot assign requested address
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
Exec. Successful
install dmt for mt7510
Load tc3162 dmt !
TCSUPPORT_WLAN
TCSUPPORT_WLAN_MT7615
TCSUPPORT_MAP_FILTER
ifconfig: SIOCGIFFLAGS: No such device
**************lan port init*****************
four ports
CPU 3 Unable to handle kernel paging request at virtual address 00000000, epc == 00000000, ra == 802e48dc
Oops[#1]:
CPU: 3 PID: 331 Comm: ethphxcmd Tainted: P O 3.18.21 #1
task: 8a1626b8 ti: 89c58000 task.ti: 89c58000
$ 0 : 00000000 00000008 00000000 00000000
$ 4 : 00000000 00000000 00000000 00000000
$ 8 : 00000000 00000000 00000000 00000000
$12 : 00000000 7721a450 00000000 00000000
$16 : 00000000 89c5bda8 89c5bda8 00000000
$20 : ffffffff 00480000 00486437 0055483c
$24 : 00000000 8021adf4
$28 : 89c58000 89c5bd78 7f91d6b0 802e48dc
Hi : 00000369
Lo : 00001be5
epc : 00000000 (null)
Tainted: P O
ra : 802e48dc generic_mii_ioctl+0x8c/0x158
Status: 11000003 KERNEL EXL IE
Cause : 5080d008
BadVA : 00000000
PrId : 0001992f (MIPS 1004Kc)
Modules linked in: hw_nat(PO) ebt_policer ebt_ip6 ebt_ip ebtable_filter ebtable_broute ebtables sch_prio sch_htb cls_fw act_mirred mapfilter(O) mt7615_ap(O) tc3162_dmt(PO) qdma_wan(PO) eth_ephy(PO) eth(PO) qdma_lan(PO) fe_core(PO) crypto_k(PO) sif(PO) detectprtype(PO) tccicmd(PO) tcledctrl(PO) speedtest(PO) tcvlantag(O) tcportbind(O) tcsmux(O) module_sel(PO)
Process ethphxcmd (pid: 331, threadinfo=89c58000, task=8a1626b8, tls=7724a460)
Stack : 7f91d6b0 c049e030 11000003 00000369 00001be5 ffffff86 89c5be40 c049e054
ffffffff 89c5be3c 804c12e8 8e8f9000 00000000 00000000 ffffffff 80264804
ffffffff 00000000 00000000 00000000 8cea7000 00008947 89c5be40 80344c10
00020aff ffffffff 00000001 89c5be40 00008947 80344d68 8e8f9000 00000020
805b5c40 00008947 00438d20 80345118 8e8fa92c 00000007 00000000 00000000
...
Call Trace:
[<c049e030>] eth_lan_mac_ioctl+0x90/0x75c [eth]
[<c049e054>] eth_lan_mac_ioctl+0xb4/0x75c [eth]
[<80264804>] vsnprintf+0x94/0x49c
[<80344c10>] dev_ifsioc+0x214/0x358
[<80344d68>] dev_load+0x14/0x84
[<80345118>] dev_ioctl+0x340/0x698
[<80069a9c>] wake_bit_function+0x0/0x5c
[<8010150c>] do_vfs_ioctl+0xa0/0x6cc
[<80106d34>] dput+0x28/0x230
[<800f005c>] __fput+0x148/0x20c
[<800f0200>] fput+0x84/0xcc
[<8010d9b8>] __fdget_pos+0x10/0x5c
[<80101bdc>] SyS_ioctl+0xa4/0xb8
[<80049964>] task_work_run+0xd0/0x11c
[<800edb00>] SyS_close+0x18/0x50
[<8001b424>] handle_sys+0x124/0x144
Code: (Bad address in epc)
---[ end trace fc209f8703305ea3 ]---
Segmentation fault
rcS (222): drop_caches: 3
log cicmd 0 (wan dmt2 set largeD 2 )
taskset: invalid number '0x8'
date: invalid date '010100002012'
rcS (222): drop_caches: 3
/etc/init.d/rcS: line 1521: /userfs/bin/wpa_supplicant: not found
CO-FW parameter.......... PRODUCT_NAME_VOIP_CHECK=1
CO-FW parameter.......... VOIP_CHIP_SELECT=0
MTK DSP support
rcS (222): drop_caches: 3
voip_loader start
status:
DSPCore[Ver:TVB1.0.5.65.250-14]
[1] PCM V2.4 (Apr 22 2022 17:12:14)
PCM_INT=37
pcm[Ver:TVB1.0.5.65.250-14]
lec[Ver:TVB1.0.5.65.250-9]
Major Num:233, device: spi
spi[Ver:TVB1.0.5.65.250-14]
ST[4294938980][spi][INFO][SPI_slic_check:L1815]set slic type: ===0===
[4294938980][spi][INFO][SPI_slic_check:L1816]Aset interface_type: ===1===
[4294938981][spi][INFO][SPI_slic_check:L1817]set slicid: ===0===
[4294938981][spi][INFO][SLIC_Reset_Infc:L1504]======slic reset 7512======
[4294938982][spi][INFO][SPI_Reset:L383]
SPI_Reset 2
RT CHECK ZARLIN ZSI
[4294938989][spi][INFO][SPI_slic_check:L1843]======spi check zarlink======
[4294938989][spi][INFO][SPI_slic_check:L1859]res_arr[0]:0x0
res_arr[1]:0x0
[4294938990][spi][INFO][SPI_slic_check:L1926][zarlink] unknown slic type!reset times:1
[4294938991][spi][INFO][SLIC_Reset_Infc:L1504]======slic reset 7512======
[4294938991][spi][INFO][SPI_Reset:L383]
SPI_Reset 2
[4294938998][spi][INFO][SPI_slic_check:L1843]======spi check zarlink======
[4294938998][spi][INFO][SPI_slic_check:L1859]res_arr[0]:0x0
res_arr[1]:0x0
[4294938999][spi][INFO][SPI_slic_check:L1926][zarlink] unknown slic type!reset times:2
[4294939000][spi][INFO][SLIC_Reset_Infc:L1504]======slic reset 7512======
[4294939000][spi][INFO][SPI_Reset:L383]
SPI_Reset 2
[4294939007][spi][INFO][SPI_slic_check:L1843]======spi check zarlink======
[4294939007][spi][INFO][SPI_slic_check:L1859]res_arr[0]:0x0
res_arr[1]:0x0
[4294939008][spi][INFO][SPI_slic_check:L1926][zarlink] unknown slic type!reset times:3
[4294939009][spi][INFO][SLIC_Reset_Infc:L1504]======slic reset 7512======
[4294939009][spi][INFO][SPI_Reset:L383]
SPI_Reset 2
[4294939016][spi][INFO][SPI_slic_check:L1843]======spi check zarlink======
[4294939016][spi][INFO][SPI_slic_check:L1859]res_arr[0]:0x0
res_arr[1]:0x0
[4294939017][spi][INFO][SPI_slic_check:L1926][zarlink] unknown slic type!reset times:4
[4294939018][spi][INFO][SLIC_Reset_Infc:L1504]======slic reset 7512======
[4294939018][spi][INFO][SPI_Reset:L383]
SPI_Reset 2
[4294939025][spi][INFO][SPI_slic_check:L1843]======spi check zarlink======
[4294939025][spi][INFO][SPI_slic_check:L1859]res_arr[0]:0x0
res_arr[1]:0x0
[4294939026][spi][INFO][SPI_slic_check:L1926][zarlink] unknown slic type!reset times:5
param.data:
[4294939027][spi][INFO][SPI_slic_check:L1815]set slic type: ===1===
[4294939027][spi][INFO][SPI_slic_check:L1816]set interface_type: ===2===
[4294939028][spi][INFO][SPI_slic_check:L1817]set slicid: ===0===
[4294939029][spi][INFO][SLIC_Reset_Infc:L1504]======slic reset 7512======
[4294939029][spi][INFO][SPI_Reset:L383]
SPI_Reset 2
START CHECK SILICON ISI
[4294939036][spi][INFO][SPI_slic_check:L1938]======spi check silicon======
[4294939036][spi][INFO][SPI_slic_check:L1950]Part_num 0x1, Revision 0x3
[4294939037][spi][INFO][SPI_slic_check:L2016]si32280 device verify success
param.data:si32280
[SLIC] si32280
Loading si32280,slic num:1
========fxs3 init========20220506
.
init mod-slic3-20220506-2
slic3[Ver:TVB1.0.5.65.250-14]
mode=
ISI
slic ready now
Loading common
init mod-ksocket
ksocket[Ver:TVB1.0.5.65.1-5]
ortp[Ver:TVB1.0.5.65.250-12]
init mod-acodec
acodec[Ver:TVB1.0.5.65.250-9]
init mod-foip3
foip3[Ver:TVB1.0.5.65.250-9]
Silabs SLIC type selected by SW makefile compile option
deviceNum=1,fxsNum=2,fxoNum=0,interfaceType=2,slicType=1,pcm1ChNum=2,pcm2ChNum=0
init gpio and clocksrc,interface:2,devNum:1,gpio:80000
ISI
[4294939153][spi][INFO][SPI_Reset:L383]
SPI_Reset 2
slic deviceVerify ProSLIC_Version 9.1.0
Silabs SLIC Reset
REG_0 = 0xcb ,device[0], Part_num 0x1, Revision 0x3
device[0]:deviceVerify Success!
SPI Reset times:1
pcm1 ch num:2 pcm2 ch num:0
fxs[Ver:TVB1.0.5.65.250-14]
[fxs_init_action](571)noinit=0
pcm1 ch num:2 pcm2 ch num:0
Init fxsNum(2) + fxoNum(0) = slic_ch_num(2) , deviceNum(1)
deviceInit on DeviceId = 0
ProSLIC_createControlInterface = 0
ProSLIC_createDevice = 0
get_start_chanid=0
ProSLIC_createChannel = 0
ProSLIC_SWInitChan = 0
device [0] chanPvt[0].chanType 1
device [0] chanPvt[0].chipType 7
ProSLIC_createChannel = 0
ProSLIC_SWInitChan = 0
device [0] chanPvt[1].chanType 1
device [0] chanPvt[1].chipType 7
Si3228x_Init_with_Options(470) size = 2 init_opt = 0
SiVoice: Channel 0: Type = PROSLIC Rev = 3
SiVoice: Channel 1: Type = PROSLIC Rev = 3
ProSLIC:loading patch: 10292015
.
Si3228x: VBAT @ 50ms = 58.692 v
Si3228x: VBAT Up = 58.901 v
Si3228x: VBAT @ 50ms = 58.272 v
Si3228x: VBAT Up = 58.272 v
Si3228x: : ProSLIC initialization completed.
ProSLIC:Starting LB Cal on channel 0
.
ProSLIC:Starting LB Cal on channel 1
___ COUNTRY SETTING ___
ring_idx : 0
imp_idx : 0
ProSLIC:PCMStart
ProSLIC:PCMStart
slic_set_gainLv - 0 / fffffffa
Bypass deviceInit on Device 0!
slic_set_gainLv - 0 / fffffffa
init mod-vdsp for 2 channels 4 sessions
vdsp[Ver:TVB1.0.5.65.250-14]
===============================
|| MTK DSP init successfully ||
===============================
fxsSetLine[1]state 0x9 State UNKNOWN !
fxsGetLine(0)Ret[1]=State[3]
fxsGetLine(1)Ret[1]=State[3]
voip loader end
taskset: invalid number '0x8'
pid 360's current affinity mask: 1
pid 360's new affinity mask: 8
taskset: invalid number '0x8'
taskset: invalid number '0x8'
taskset: invalid number '0x8'
Power Manager 0.2 init
wan ether support
Usage: echo "cid regStat" > /proc/fxs/sipRegLed
Usage: <cid>=(0|1), 0-channel0, 1-channel1
Usage: <regStat>=(0|1|2), 0-light off, 1-light on, 2-light blink
Usage: echo "cid regStat" > /proc/fxs/sipRegLed
Usage: <cid>=(0|1), 0-channel0, 1-channel1
Usage: <regStat>=(0|1|2), 0-light off, 1-light on, 2-light blink
VDSP_GetInstance:278
fxsSetLine[0]state 0x9 State UNKNOWN !
Dying Gasp 0.31 init
oenmap 0 oenmap2 0
TCSUPPORT_WLAN_SW_RPS
ecnt_rps_napi_init===
fxsSetLine[1]state 0x9 State UNKNOWN !
/proc/net/skbmgr_4k_limit ???
Jan 1 00:00:33 crond[416]: crond: crond (busybox 1.20.1) started, log level 8
START disable Lan and Wan...
Bookmarks