Hello,
I have ADSL from OTE with ZTE H108NS modem and my own OpenWrt (14.07) based router. I have modem in Bridge mode and I would like to setup IPv6, but IPv6 in modem web interface says "Not connected" while IPv4 says "Connected". When I use modem in PPPoE mode (not as bridge), it gets IPv6 address without problem and this address is then passed to OpenWrt LAN interface - I have modem connected both LAN and WAN with two cables - WAN for PPPoE and LAN in order to access web interface of modem from LAN.
I tried to use configuration from article (and comment) from following site, but I cannot get it working. Article is also quite old.
http://ipv6.ote.gr/?page_id=522
Can someone help me get it working?
Thank you in advance.
Εμφάνιση 1-7 από 7
-
30-09-15, 10:51 How to configure IPv6 with ZTE H108NS in Bridge mode on OpenWrt router behind? #1
-
30-09-15, 12:30 Απάντηση: How to configure IPv6 with ZTE H108NS in Bridge mode on OpenWrt router behind? #2
I also have a similar setup with you (Speedtouch 585i v6 with Openwrt 14.07) . A few days before i noticed the WAN interface of my Openwrt router having an IPv6 ip address, which never happened before. I did not make any change for that. Login at the Openwrt router with SSH and check that at the file /etc/config/network the wan interface has the setting option 'ipv6' '1' . If you make any change at that file with SSH, in order to be activated, you have either to give the command /etc/init.d/network restart or to reboot the Openwrt router. Also try to replace @otenet.gr at your wan username with @ipv6ote.gr . If you have again any problem write us again
Τελευταία επεξεργασία από το μέλος dimangelid : 30-09-15 στις 18:33.
-
30-09-15, 14:36 Απάντηση: How to configure IPv6 with ZTE H108NS in Bridge mode on OpenWrt router behind? #3
Hello,
I already did what you say, it is part of the official guide from OTE and also in other guides. No progress. Any ideas? :-)
/etc/config/network
Κώδικας:config interface 'loopback' option ifname 'lo' option proto 'static' option ipaddr '127.0.0.1' option netmask '255.0.0.0' config globals 'globals' option ula_prefix 'auto' config interface 'lan' option type 'bridge' option proto 'static' option netmask '255.255.255.0' option dns '8.8.8.8 8.8.4.4' option ipaddr '192.168.20.1' option _orig_ifname 'eth0 eth1 wlan1' option _orig_bridge 'true' option ifname 'eth0 eth1 tap0' option ip6assign '64' config switch option name 'switch0' option reset '1' option enable_vlan '1' config switch_vlan option device 'switch0' option vlan '1' option ports '0 1 2 3 4 ' config switch_vlan option device 'switch0' option vlan '2' option ports '5 6' config interface 'WAN' option proto 'pppoe' option ifname 'eth2' option password '*****' option ipv6 '1' option mtu '1492' option username '****@otenet.gr' #this makes no difference: #option username '****@ipv6ote.gr'
-
30-09-15, 18:35 Απάντηση: How to configure IPv6 with ZTE H108NS in Bridge mode on OpenWrt router behind? #4
I have no further ideas, as i have deactivated ipv6 on my Openwrt router. I suggest you flash your router with the latest available Openwrt version and try again. Also i made a mistake at my first message, my router also has OpenWRT 14.07 (build 10530) . If you have no results with the update inform us and wait 1-2 days in order to see if someone else knows what it happens. Otherwise you can call OTE at 13888 and tell them what happens.
-
01-10-15, 02:20 Απάντηση: How to configure IPv6 with ZTE H108NS in Bridge mode on OpenWrt router behind? #5
So I decided to completely reflash my router and restore factory settings. After that, IPv6 started working as it should, just with "option ipv6 '1". :-)
In modem interface, I still can see under IPv6:
Status:Not Connected
Who cares, there are more options there, which probably doesnt work and have on effect in Bridge mode...
It will take few days to configure everything again, because I want to avoid of importing backup. I am actually very happy with this solution, much better than fight with issue in modem or at OTE side... :-)
Thanks
-
01-10-15, 04:36 Απάντηση: How to configure IPv6 with ZTE H108NS in Bridge mode on OpenWrt router behind? #6
.Did you just reset to OpenWRT defaults or flashed 15.05 and reset? In any case i'm glad that you solved your problem Don't care about what the ZTE says at its menu, you are in bridge mode and the ZTE just handles the ADSL synchronisation, nothing else. All the other stuff (including IPv6) are handled by your OpenWRT router! In my case my modem (good old Speedtouch 585i v6) does not support IPv6 at all. But i can get an IPv6 address if i remove option 'ipv6' '0'
-
01-10-15, 09:43 Απάντηση: How to configure IPv6 with ZTE H108NS in Bridge mode on OpenWrt router behind? #7
I reflashed whole system to the latest availiable version for my device, which is same as before, thanks to automatic updates. I had more reasons to do that, like changing file system from JFFS2 to UBIFS, updating recovery system and so. Part of this process was factory reset which maybe would solved issues itself.
Basically I just entered PPPoE credentials and it got IPv6 working.
Someone could find configuration helpfull.
/etc/config/network
Κώδικας:config interface 'loopback' option ifname 'lo' option proto 'static' option ipaddr '127.0.0.1' option netmask '255.0.0.0' config globals 'globals' option ula_prefix ****:****:****::/48' config interface 'lan' option ifname 'eth0 eth1' option force_link '1' option type 'bridge' option proto 'static' option netmask '255.255.255.0' option ip6assign '60' option ipaddr '192.168.20.1' config interface 'wan' option ifname 'eth2' option proto 'pppoe' option username '*****@otenet.gr' option password '******' option ipv6 '1' config interface 'wan6' option ifname '@wan' option proto 'dhcpv6' config switch option name 'switch0' option reset '1' option enable_vlan '1' config switch_vlan option device 'switch0' option vlan '1' option ports '0 1 2 3 4 ' config switch_vlan option device 'switch0' option vlan '2' option ports '5 6'
Κώδικας:config dnsmasq option domainneeded '1' option boguspriv '1' option filterwin2k '0' option localise_queries '1' option rebind_protection '1' option rebind_localhost '1' option local '/lan/' option domain 'lan' option expandhosts '1' option nonegcache '0' option authoritative '1' option readethers '1' option leasefile '/tmp/dhcp.leases' option resolvfile '/tmp/resolv.conf.auto' option port '0' config dhcp 'lan' option interface 'lan' option start '100' option limit '150' option leasetime '12h' option dhcpv6 'server' option ra 'server' option ignore '0' list dhcp_option '6,192.168.20.1' config dhcp 'wan' option interface 'wan' option ignore '1' config odhcpd 'odhcpd' option maindhcp '0' option leasefile '/tmp/hosts/odhcpd' option leasetrigger '/usr/sbin/odhcpd-update'
Παρόμοια Θέματα
-
Mikrotik IPv6 σε PPPoE client με modem σε bridge mode
Από deniSun στο φόρουμ MikroTik ADSL modems, routers & routerBOARDsΜηνύματα: 136Τελευταίο Μήνυμα: 24-05-23, 22:17 -
Επιτέλους Bridge mode σε ZTE ZXHN H168N
Από iliteo στο φόρουμ Vodafone VDSLΜηνύματα: 260Τελευταίο Μήνυμα: 19-02-21, 23:46 -
ZTE ZXV10 H201L(bridge mode) + tp-link wd741
Από KeyMaKeR στο φόρουμ ADSLΜηνύματα: 4Τελευταίο Μήνυμα: 04-04-15, 03:40 -
ZTE ZXV10 H201L bridge mode
Από manospcistas στο φόρουμ ADSLΜηνύματα: 1Τελευταίο Μήνυμα: 13-11-14, 15:18
Bookmarks