Περί ROS ο λόγος...

[deniSun]

Εμένα ακόμα να μου βρει λύση για αυτό.
Μου απάντησαν μετά από πολλές μέρες καθυστέρηση.
Μου ζήτησαν και τους έστειλα 2-3 supout και εδώ και 1 εβδομάδα ακόμα περιμένω απάντηση.

[BillyVan]

καλησπερα, για πες δλδ? γιατι την περναω τωρα παντου.

Στο φορουμ τους αναφερει ενας.

Some of my routers are HAP AC2. Not getting worse but not any better.
I can tell if 6.43.16 still faster n more stable than 6.44.6 to 6.46.6.
Problem? Yes.
1. Sometimes wireless G cant connect, while wireless N can always connect n working just fine. Mode bgn. 6.43.16 dont have this issue.
2. Some installation at office building with alot of noise, 6.43.16 perform better for 2.4ghz.
3. PPTP from android phone, will go disconnect in few mins. With 6.43.16, the same phone can connected for hours without any problem.
Most installation still with 6.43.16 n will stay at 6.43.16 until MT can make another real stable version.

[Nikiforos]

Στο φορουμ τους αναφερει ενας.

Some of my routers are HAP AC2. Not getting worse but not any better.
I can tell if 6.43.16 still faster n more stable than 6.44.6 to 6.46.6.
Problem? Yes.
1. Sometimes wireless G cant connect, while wireless N can always connect n working just fine. Mode bgn. 6.43.16 dont have this issue.
2. Some installation at office building with alot of noise, 6.43.16 perform better for 2.4ghz.
3. PPTP from android phone, will go disconnect in few mins. With 6.43.16, the same phone can connected for hours without any problem.
Most installation still with 6.43.16 n will stay at 6.43.16 until MT can make another real stable version.

Καλησπέρα, ευχαριστω, προς το παρον απο χτες που το εβαλα οσο το δοκιμασα δεν ειδα προβλημα στο wireless 2,4 και 5ghz και pptp δεν εχω εδω και χρονια.
Στο 109 τωρα που παιζει OVPN server + client κανενα προβλημα ομως.

[deniSun]

6.45.9 Long Term changelog :
Changes since 6.45.8:

Spoiler:

*) arm - improved watchdog and kernel panic reporting in log after reboots on RB3011 and IPQ4018/IPQ4019 devices ("/system routerboard upgrade" required);
*) capsman - fixed "certificate" parameter updating on CAP;
*) certificate - fixed certificate verification when flushing CRL's;
*) chr - added support for file system quiescing;
*) chr - enabled support for VMBus protocol version 4.1;
*) chr - fixed graceful shutdown execution on Hyper-V (introduced in v6.46);
*) chr - improved system stability when running CHR on Hyper-V;
*) console - prevent incorrect type interfaces appearing in command hints;
*) crs3xx - fixed frame forwarding after disabling/enabling bridge hardware offloading for CRS354-48G-4S+2Q+ device;
*) crs3xx - fixed interface statistics for CRS354-48G-4S+2Q+ and CRS354-48P-4S+2Q+ devices;
*) crs3xx - fixed switch rule "dst-port" parameter for IPv6 traffic on CRS305-1G-4S+, CRS326-24G-2S+, CRS328-24P-4S+, CRS328-4C-20S-4S+, netPower 15FR devices;
*) crs3xx - improved SFP+ DAC cable initialization for CRS326-24S+2Q+ device;
*) defconf - added welcome note with common first steps for new users;
*) discovery - do not send CDP and LLDP packets on interfaces that does not have MAC address;
*) health - fixed maximum SFP temperature reading under '/system health' menu;
*) hotspot - fixed redirect to log in page (introduced in v6.45);
*) ike1 - rekey phase 1 rekeying as responder for Windows initiators;
*) ipsec - improved system stability when handling fragmented packets;
*) led - added "dark-mode" functionality for CRS105-5S-FB;
*) lte - added "phy-cellid" value support for LTE-US;
*) lte - fixed IP type selection from APN on RBSXTLTE3-7;
*) lte - improved system stability when performing firmware update on R11e-LTE6;
*) sniffer - fixed minor typo in "host" menu;
*) snmp - fixed "ifSpeed" reporting for tunnel interfaces;
*) snmp - fixed "routeros-version" value returning from registration table;
*) snmp - fixed UPS battery voltage value scaling;
*) ssh - added support for RSA keys with SHA256 hash (RFC8332);
*) system - correctly handle Generic Receive Offloading (GRO) for MPLS traffic;
*) system - improved system stability when forwarding traffic from switch chip to CPU (introduced in v6.43);
*) system - improved system stability when receiving/sending TCP traffic on multicore devices;
*) traceroute - improved stability when invalid packet is received;
*) webfig - added default configuration confirmation window to WebFig;
*) webfig - allow skin designing without "ftp" and "sensitive" policies;
*) webfig - do not show WebFig menu when opening 'Check For Updates' in Quick Set;
*) winbox - added "Options" parameter support for DHCPv6 client and server;
*) winbox - added 160Mhz extension channel support for CAPsMAN;
*) winbox - added support for "Tools->WoL" menu;
*) winbox - do not show "Revision" parameter under "System/RouterBOARD" menu on devices that have only one revision;
*) winbox - fixed "ARP" parameter inheritance from "CAPs Configuration" configuration;
*) winbox - fixed "Bands" parameter display for LTE interfaces;
*) winbox - fixed "DSCP" parameter value setting;
*) winbox - fixed "Frequency" and "Secondary Frequency" parameter inheritance from "CAPs Channel" configuration;
*) winbox - fixed "Passthr. MAC Address" parameter display "LTE APNs" menu;
*) winbox - fixed "Switch" menu on CRS354-48P-4S+2Q+;
*) winbox - fixed "dst-port" unsetting in "IP->Hotspot->Walled Garden" menu;
*) winbox - fixed "invalid" flag presence under "System/Certificates/CRL" menu;
*) winbox - fixed automatic "IPv6->Firewall->Address List" table update;
*) winbox - increased limit of multi-entry fields to 100;
*) winbox - made "none" the default value for "Security Profile" parameter when creating a new "Wirelees->Connect list" entry;
*) winbox - renamed "Memory used" to "HDD used" for HDD type under "Tools->Graphing->Resource Graphs";
*) winbox - renamed "Routerboard" to "RouterBOARD" under "System/RouterBOARD" menu;
*) winbox - show "System/RouterBOARD/Mode Button" on devices that have such feature;
*) wireless - added "skip-dfs-channels" parameter;
*) wireless - allow using FCC "U-NII-2" frequency range for hAP ac2 and RBwAPGR series devices;
*) wireless - fixed default "antenna-gain" setting on SXT 2 devices;
*) wireless - improved 5GHz interface stability on RB4011iGS+5HacQ2HnD and Audience;
*) wireless - improved compatibility for "ETSI" wireless country profile;
*) wireless - improved system stability on hAP ac^2;
*) wireless - updated "bangladesh" regulatory domain information;
*) wireless - updated "indonesia4" regulatory domain information;
*) wireless - updated "south africa" regulatory domain information;

[deniSun]

winbox
What's new in v3.24:

Spoiler:

*) fixed WinBox crash when viewing firewall rule with src/dst-address-type configured;
*) fixed checkbox group disabled state inheritance;
*) fixed dates and times in interface link up/down properties (RouterOS v6.47 required);
*) fixed system comment message display;
*) fixed vertical font alignment in optional fields;
*) fixed window size inheritance from the previous session;
*) keep advanced and simple mode table settings separately;
*) make WinBox upgrade work with wine 5.0 or newer;
*) properly show popup windows on top;

[macro]

To window size φτιαχτηκε σιγουρα? Γιατι ετσι λεγανε και για το 3.23........

[deniSun]

To window size φτιαχτηκε σιγουρα? Γιατι ετσι λεγανε και για το 3.23........

Όχι. Είναι οκ.
Το δοκίμασα.
Έκανα resize παράθυρο και το κράτησε.
Επίσης άνοιξα/έκλεισα και όλα έμειναν όπως πριν.

[jkarabas]

Όχι. Είναι οκ.
Το δοκίμασα.
Έκανα resize παράθυρο και το κράτησε.
Επίσης άνοιξα/έκλεισα και όλα έμειναν όπως πριν.

Καλημέρα
Άντε επιτέλους!!!

[geioannou]

Καλησπερα. ενδιαφερομαι να κανω μια αγορα ενος MikroTik hAP ac². Μπορει καποιος να μου πει εαν γνωριζει εαν εχει επιλογη πολλαπλων SSID ?
Φανταζομαι θα γινεται ειτε σαν απ' ευθειας εντολη ειτε σαν virtual AP, αλλα μπορει να επιβεβαιωσει καποιος ?
ευχαριστω

[zark]

Πέρα από τα 2 ξεχωριστά wireless interfaces που έχει για 5ghz και 2.4ghz, μπορείς να ορίσεις όσα virtual wireless interfaces θες κάτω απ'αυτά.

[geioannou]

Πέρα από τα 2 ξεχωριστά wireless interfaces που έχει για 5ghz και 2.4ghz, μπορείς να ορίσεις όσα virtual wireless interfaces θες κάτω απ'αυτά.

μαλιστα, καταλαβα. πολυ ωραια.
το εχεις, απο εμβελεια ειναι οκ?
εχω ακουσει καλα λογια απο τα reviews

[Nikiforos]

μαλιστα, καταλαβα. πολυ ωραια.
το εχεις, απο εμβελεια ειναι οκ?
εχω ακουσει καλα λογια απο τα reviews

Καλησπερα, εγω το εχω παντως και σκιζει, απο τα καλυτερα πραγματα που εχω αγορασει ποτέ....
Και μαλιστα πλεον το εχω να ρουταρει την INALAN γιατι το 109 με μονοπυρηνη cpu δεν αντεχε τα 200+ mbps up/down, ενω αυτο εχει 4πυρηνη ARM στα 716 κιολας.
Επισης υποστηριζει DUDE server που νομιζω θα σε ενδιαφερει εσενα.
Τελος το μοναδικο μειονεκτημα η μικρη εσωτερικη μνημη δεν χωραει δλδ πολλα πακετα, οποτε πρεπει να κανεις επιλογες.

Υ.Γ το ξερεις οτι ειμαστε σε λαθος θεμα?

[geioannou]

- Ευχαριστω για τις απαντησεις. εκανα παραγγελια!!
- Ε δεν ειμαι και τελειως εκτος! κατι για το μενου του ROS ρωτησα σε ενα συγκεκριμενο μηχανακι !!!
)))

[Nikiforos]

- Ευχαριστω για τις απαντησεις. εκανα παραγγελια!!
- Ε δεν ειμαι και τελειως εκτος! κατι για το μενου του ROS ρωτησα σε ενα συγκεκριμενο μηχανακι !!!
)))

η πρωτη ερωτηση μπορεις να πεις οκ, μετα ξεφυγαμε.
Απλα το λέω για να μην μπερδευουμε τα θεματα.
Αυτο με τα πολλαπλα SSID γινεται κανοντας πολλα Virtual AP, οπως θα ξερεις ομως πρεπει να εχουν ολα αναγκαστικα την ιδια συχνοτητα, αλλα και ισχυ.

[deniSun]

RouterOS version 6.47 has been released in public "stable" channel!
What's new in 6.47 (2020-Jun-02 07:38):

Important note!!!

- The Dude server must be updated to monitor v6.46.4 and v6.47beta30+ RouterOS type devices.
- The Dude client must be manually upgraded after upgrading The Dude server.
- The Dude requires "winbox" policy instead of "dude" to monitor v6.46.4 and v6.47beta30+ RouterOS type devices.
- Make sure LTE APN Profile name does not match any of the DHCP server's names if LTE passthrough is used.

MAJOR CHANGES IN v6.47:
----------------------
!) dns - added client side support for DNS over HTTPS (DoH) (RFC8484);
!) socks - added support for SOCKS5 (RFC 1928);
!) user - enable "winbox" policy for groups with "dude" policy automatically on upgrade;
----------------------

Changes in this release:

Spoiler:

*) api - added ECDHE cipher support for "api-ssl" service;
*) bonding - improved slave interface MAC address handling;
*) bonding - prefer primary slave MAC address for bonding interface;
*) branding - do not ask to confirm configuration applied from branding package;
*) branding - fixed identity setting from branding package;
*) branding - improved branding package installation process when another branding package is already installed;
*) bridge - added logging debug message when a host MAC address is learned on a different bridge port;
*) bridge - added warning message when a bridge port gets dynamically added to VLAN range;
*) bridge - correctly remove disabled MSTI;
*) bridge - improved hardware offloading enabling/disabling;
*) certificate - added "skid" and "akid" values for detailed print;
*) certificate - allow dynamic CRL removal;
*) certificate - disabled CRL usage by default;
*) certificate - do not use SSL for first CRL update;
*) chr - added support for file system quiescing;
*) chr - added support for hardware watchdog on ESXI;
*) chr - enabled support for VMBus protocol version 4.1;
*) chr - improved system stability when running CHR on Hyper-V;
*) crs3xx - correctly remove switch rules on CRS317-1G-16S+ and CRS309-1G-8S+ devices;
*) crs3xx - fixed "ingress-rate" property on CRS309-1G-8S+, CRS312-4C+8XG, CRS326-24S+2Q+ devices;
*) crs3xx - fixed hardware offloaded bonding on Ethernet interfaces for CRS354 devices;
*) crs3xx - improved 10G interface initialization on CRS312 devices;
*) crs3xx - improved switch host table updating;
*) crs3xx - show correct switch model for netPower 15FR device;
*) defconf - fixed default configuration initialization if power loss occurred during the process;
*) dhcpv4 - added end option (255) validation for both server and client;
*) dhcpv4-client - improved stability when changing client while still receiving advertisements;
*) dhcpv4-server - disallow zero lease-time setting;
*) dhcpv6-client - improved error logging when when renewed address differs;
*) dhcpv6-server - do not require "server" parameter for bindings;
*) dhcpv6-server - fixed MAC address retrieving from DUID when timestamp is present;
*) discovery - do not send discovery packets on inactive bonding slave interfaces;
*) discovery - do not send discovery packets on interfaces that are blocked by STP;
*) disk - improved disk management service stability when receiving bogus packets;
*) disk - improved recently created file survival after reboots;
*) dns - added support for exclusive dynamic DNS server usage from IPsec;
*) dns - added support for forwarding DNS queries of static entries to specific server;
*) dns - added support for multiple type static entries;
*) dot1x - added "radius-mac-format" parameter;
*) dot1x - added hex value support for RADIUS switch rules;
*) dot1x - added range "dst-port" support for RADIUS switch rules;
*) dot1x - added support for lower case "mac-auth" RADIUS formats;
*) dot1x - fixed "reject-vlan-id" value range;
*) dot1x - fixed dynamically created switch rule removal when client disconnects;
*) dot1x - fixed port blocking when interface changes state from disabled to enabled;
*) dot1x - improved Dot1X service stability when receiving bogus packets;
*) dot1x - improved debug logging output to "dot1x" topic;
*) dot1x - improved value validation for dynamically created switch rules;
*) email - added support for multiple "to" recipients;
*) ethernet - fixed interface stopping responding after blink command execution on CCR2004-1G-12S+2XS;
*) fetch - fixed "User-Agent" usage if provided by "http-header-field";
*) graphing - improved graphing service stability when receiving bogus packets;
*) health - added "gauges" submenu with SNMP OID reporting;
*) health - improved stability for system health monitor on CCR2004-1G-12S+2XS;
*) hotspot - updated splash page design ('/ip hotspot reset-html' required);
*) ike1 - added error message when specifying "my-id" for XAuth identity;
*) ike1 - added support for "UNITY_DEF_DOMAIN" and "UNITY_SPLITDNS_NAME" payload attributes;
*) ike1 - do not try to keep phase 2 when purging phase 1;
*) ike1 - improved policy lookup with specific protocol;
*) ike1 - improved stability when performing policy lookup on non-existant peer;
*) ike2 - added support for "INTERNAL_DNS_DOMAIN" payload attribute;
*) ike2 - added support for RADIUS Disconnect-Request message handling;
*) ike2 - added support for RFC8598;
*) ike2 - allow initiator address change before authentication;
*) ike2 - fixed authentication handling when initiator disconnects before RADIUS response;
*) interface - improved system stability when receiving bogus packets;
*) interface - increased loopback interface MTU to 65536;
*) ipsec - added "split-dns" parameter support for mode configuration;
*) ipsec - added "use-responder-dns" parameter support;
*) ipsec - allow specifying two peers for a single policy for failover;
*) ipsec - control CRL validation with global "use-crl" setting;
*) ipsec - do full certificate validation for identities with explicit certificate;
*) ipsec - fixed minor spelling mistake in logs;
*) ipsec - improved IPsec service stability when receiving bogus packets;
*) ipsec - place dynamically created IPsec policies by L2TP client at the begining of the table;
*) kidcontrol - ignore IPv6 multicast MAC addresses;
*) l2tp - added "src-address" parameter for L2TP client;
*) l2tp - added "use-peer-dns" parameter for L2TP client;
*) l2tp - improved dynamically created IPsec configuration updating;
*) l2tp - use L2TP interface when adding dynamic IPsec peer;
*) lcd - fixed LCD service becoming unavailable on devices without LCD screen;
*) lcd - improved general system stability when LCD is not present;
*) led - fixed minor typo in LED warning message;
*) log - added logging entry when changing user's password;
*) log - added tunnel endpoint address to establishment and disconnect logging entries;
*) log - made startup script failures log as critical errors;
*) lte - added support for Huawei K5161 modem;
*) lte - added support for NEOWAY N720;
*) lte - added support for multiple passthrough APN configuration;
*) lte - do not allow running "scan" on R11e-4G;
*) lte - fixed "allow-roaming" setting when using LTE network mode on R11e-LTE;
*) lte - fixed "band" parameter persistence after disable/enable;
*) lte - fixed "ecno" and "rscp" value reporting on R11e-LTE6;
*) lte - fixed VLAN interface passthrough support;
*) lte - fixed multiple APN reactivation after deactivation by operator;
*) lte - improved stability during firmware upgrade;
*) lte - made "mac-address" parameter read-only;
*) lte - show "phy-cellid" value only in LTE mode;
*) netinstall - removed "Flashfig" from Netinstall;
*) netinstall - removed "Make Floppy" from Netinstall;
*) netinstall - signed netinstall.exe with Digital Signature;
*) netwatch - improved Netwatch service stability when invalid configuration values are passed;
*) ovpn - added "use-peer-dns" parameter for OVPN client;
*) port - removed serial console port on hEX S;
*) ppp - added "Acct-Session-Id" attribute to "Access-Request" messages;
*) ppp - added support for ZTE MF90;
*) ppp - fixed minor typo when running "info" command;
*) ppp - removed "comment", "set" and "edit" commands from "PPP->Active" menu;
*) pptp - added "use-peer-dns" parameter for PPTP client;
*) profile - added support for CCR2004-1G-12S+2XS;
*) proxy - increased minimal free RAM that can not be used for proxy services;
*) qsfp - added support for FEC mode (fec74), with the FEC mode disabled by default;
*) quickset - do not show "SINR" field in Quick Set when there is no data;
*) quickset - fixed invalid configuration applying when performing changes during LTE modem initialization process;
*) quickset - removed "EARFCN" field from Quick Set;
*) quickset - removed "LTE band" setting from Quick Set;
*) quickset - show "Antenna Gain" setting on devices without built-in antennas;
*) quickset - use "station-wds" mode when connecting to AP with RouterOS flag;
*) route - improved system stability after reboot with large amount of VLAN interfaces with PPPoE servers attached;
*) routerboard - added "hold-time" parameter to mode-button menu;
*) routerboard - added "reset-button" menu - custom command execution with reset button;
*) routing - improved IGMP-Proxy service stability when receiving bogus packets;
*) routing - improved routing service stability when receiving bogus packets;
*) sfp28 - added support for FEC modes (fec74 and fec91), with fec91 mode already enabled by default;
*) sniffer - allow setting port for "streaming-server";
*) snmp - added "dot1qTpFdbTable" OID reporting for Q-BRIDGE-MIB;
*) snmp - changed "upsEstimatedMinutesRemaining" reported value from seconds to minutes;
*) snmp - fixed "dot1dBasePort" index offset for BRIDGE-MIB;
*) snmp - improved OID policy checking and error reporting on "set" command;
*) snmp - improved stability when polling MAC address related OID;
*) ssh - improved SSH service stability when receiving bogus packets;
*) supout - added "dot1x" section to supout files;
*) supout - improved UPS information reporting;
*) switch - correctly display switch statistics when all switch ports are disabled on RTL8367 switch chip;
*) switch - correctly enable and disable CPU Flow Control on RB3011UiAS;
*) switch - made "auto" the default value for "vlan-id" parameter when creating a new static host entry;
*) system - correctly handle Generic Receive Offloading (GRO) for MPLS traffic;
*) system - improved driver loading speed on startup;
*) tr069-client - added LTE firmware update functionality support;
*) tr069-client - added additional LTE information parameters;
*) tr069-client - added additional wireless registration table parameters;
*) tr069-client - added interface type parameter support;
*) tr069-client - added multiple simultaneous session support for diagnostics test;
*) tr069-client - added total connection tracking entries parameter;
*) tr069-client - removed warning log message when not using HTTPS;
*) traffic-flow - added "postDestinationMacAddress" parameter support for IPFIX and NetFlow v9;
*) upgrade - fixed space handling in package file names;
*) ups - added battery info for APC SmartUPS 2200;
*) ups - improved compatibility with APC Smart UPS 1000 and 1500;
*) user - improved user management service stability when receiving bogus packets;
*) w60g - fixed link status logging;
*) w60g - improved rate selection in low traffic conditions;
*) w60g - use "arp" and "mtu" parameters from master interface when creating a new station;
*) webfig - fixed 5 GHz wireless interface "frequency" parameter value list on Audience;
*) webfig - fixed WinBox download link;
*) webfig - fixed skin usage from branding package;
*) webfig - updated icon design;
*) winbox - added "Rate" parameter for switch ACL rules;
*) winbox - added "auth-info" parameter under "Dot1X->Active" menu;
*) winbox - added "auth-types", "comment", "mac-auth-mode" and "reject-vlan-id" parameters for Dot1X server;
*) winbox - added "auto-erase" option to "Tool/SMS" menu;
*) winbox - added "bus" parameter for "USB Power Reset" command on NetMetal ac^2;
*) winbox - added "bus" parameter for "USB Power Reset" command on RBM33G;
*) winbox - added "comment" parameter and "dynamic" flag support under "Switch->Rule" table;
*) winbox - added "comment" parameter for Dot1X client;
*) winbox - added "region" parameter for W60G interfaces;
*) winbox - added "skip-dfs-channels" parameter to wireless interface menu;
*) winbox - added comment support for "Switch->VLAN" menu;
*) winbox - added enable and disable buttons for "MPLS->MPLS Interface" table;
*) winbox - added support for inline bar graphs for LTE signal values;
*) winbox - aligned all "IP->Traffic Flow->IPFIX" check boxes in single line (WinBox v3.22 required);
*) winbox - allow setting "Primary" parameter for "balance-tlb" bonding interfaces;
*) winbox - allow to specify any Ethernet like interface under "Tool/WoL" menu;
*) winbox - do not allow to enter empty strings in "caps-man-names" and "common-name" parameters;
*) winbox - fixed "BGP Origin" value display under "IPv6->Routes" menu;
*) winbox - fixed "Data Rate" checkbox alignment (WinBox v3.22 required);
*) winbox - fixed "Tx/Rx Signal Strength" value presence for 4 chain interfaces;
*) winbox - fixed WDS usage when connecting to RouterOS access point using QuickSet;
*) winbox - fixed bonding type interface support for "Switch->Host" table;
*) winbox - fixed dates and times in interface link up/down properties (WinBox v3.24 required);
*) winbox - fixed wireless interface "HT" tab setting presence when "band=5ghz-n/ac";
*) winbox - fixed wireless sniffer parameter setting;
*) winbox - limit number of simultaneous WinBox sessions to 5 for users without "write" permission;
*) winbox - made "yes" the default value for "Inject Summary LSAs" parameter when creating a new NSSA or STUB area;
*) winbox - removed duplicate "join-eui", "dev-eui", "counter", "chain", "size" and "payload" parameters under "LoRa/Traffic";
*) winbox - renamed "Routerboard" to "RouterBOARD" under "System/RouterBOARD" menu;
*) winbox - show "Hardware Offload" parameter for bonding interfaces;
*) winbox - updated icon design;
*) wireless - added "russia 6ghz" regulatory domain information;
*) wireless - enabled unicast flood for DHCP traffic on ARM architecture access points;
*) wireless - fixed Nstreme wireless protocol performance decrease;
*) wireless - improved management service stability when receiving bogus packets;
*) wireless - updated "egypt" regulatory domain information;
*) wireless - updated "russia4" regulatory domain information;
*) www - added "tls-version" parameter in "IP->Services" menu;