Περί ROS ο λόγος...

[deniSun]

Περίμενα περισσότερα προβλήματα.

Απ ότι έχω καταλάβει τις εκδόσεις τις προβάρουν στις εκδόσεις ccr.
Αν και θυμάμαι κάποιες εκδόσεις που είχαν σοβαρά προβλήματα με τα ccr.
Από εκεί και κάτω αφήνουν τους χρήστες να κάνουν τα τεστ.

[deniSun]

What's new in 7.3rc1 (2022-May-27 11:50):

Spoiler:

*) bgp - moved "interface bgp-vpls" menu to "routing bgp vpls";
*) bgp - remove unused commands and parameters;
*) bluetooth - improved long-term service stability;
*) bridge - fixed TCP, UDP port parsing for loop detect warning;
*) capsman - fixed bridge disabling when using L2 connection;
*) ccr - improved interface link stability on CCR2004-16G-2S+PC;
*) chr - fixed Cloud DDNS update after license renewal;
*) console - fixed "terminal inkey" command;
*) crs1xx/2xx - improved system stability during switch reset;
*) defconf - do not add passthrough ports to local bridge on CCR2004-1G-2XS-PCIe;
*) ipv6 - fixed dynamic non link-local addresses displaying;
*) l2tp - added VRF support for L2TP client;
*) l3hw - greatly improved route offloading speed;
*) l3hw - log HW routes count and the shortest offloaded subnet prefix if the HW memory gets full;
*) l3hw - offload only main routing table;
*) l3hw - partial routing table offload for Marvell Prestera DX4000/DX8000 switch chip series;
*) lhgg - improved system stability (introduced in v7.2);
*) lte - improved LTE interface initialization process on LtAP-2HnD;
*) mpls - made LDP bindings work on PPP interfaces;
*) ospf - ignore instance route when originate-default=if-installed is enabled;
*) ovpn - fixed server instance not responding to incoming connections after reboot on CHR;
*) profile - added "wireguard" process classificator;
*) profile - added "zerotier" process classificator;
*) qsfp - reset module only when all ports are disabled;
*) queue - allow to set higher limits than 4G;
*) queue - display warning for CAKE type in simple and tree setups when "bandwidth" parameter is configured;
*) resource - fixed CPU type display under system resources for ARM and ARM64;
*) routerboot - prevent enabling "protected-routerboot" on unsupported factory firmware versions;
*) smb - fixed SMB2 file list reporting;
*) snmp - added VRF support;
*) ssh - fixed private key usage after downgrade;
*) winbox - added "Default Cost" parameter under "Routing/OSPF/Area" menu;
*) winbox - fixed "Type" values under "IP/Route" menu;
*) winbox - fixed minor typo in reboot confirmation prompt;
*) winbox - made wireless access list entries sortable when using the wifiwave2 package;
*) ww2 - general stability and throughput improvements;
*) x86 - added support for Solarflare SFC1920 NIC;
*) x86 - fixed soft-id reading on virtualized x86 installations (introduced in v7.2);

- - - Updated - - -

*) queue - display warning for CAKE type in simple and tree setups when "bandwidth" parameter is configured;

Υποτίθεται ότι θα το καταργήσουν.
Όσο για το πεδίο bandwidth, ποτέ δεν κατάλαβα τι ρόλο παίζει εκεί.

[BillyVan]

Ενδιαφέρον είναι και το

*) routerboot - prevent enabling "protected-routerboot" on unsupported factory firmware versions;

Μαλλον για τυπου openwrt μου κανει

[deniSun]

What's new in 7.3rc2 (2022-Jun-02 15:26):

*) capsman - fixed loss of manager configuration when "package-path" is set to external disk;
*) l2tp - fixed L2TP session handling from iOS clients (introduced in v7.3beta40);
*) ssh - fixed corrupt host key automatic regeneration;

[BillyVan]

Νεο Winbox

What's new in v3.36:

*) do not set hidden field values as empty when adding new item;
*) fixed Graphing and Quickset graphs;
*) fixed default value for disabled wireless EAP methods field;
*) fixed issue with showing non-existing values;
*) fixed managed list category grouping when value is IP with port;
*) fixed missing icon for submenus that are hidden by skin;
*) fixed neighbour table filter "all" storage;
*) fixed saving and restoring of filter comboboxes;
*) fixed skin behavior for "Add" buttons with dropdown;
*) fixed value updating when it is changed and disabled;
*) fixed values with required "&" prefix;
*) fixed wifiwave2 frequency field;
*) show error when not enough space to complete file upload;

If you experience version related issues, then please report them to support@mikrotik.com.

Both Winbox 32-bit and 64-bit versions are available here:
https://www.mikrotik.com/download

[deniSun]

Νεο Winbox

What's new in v3.36:

Δεν το έχουν ανεβάσει ακόμα στο dw.

[daltongr]

Δεν το έχουν ανεβάσει ακόμα στο dw.

What's new in v3.36:

*) do not set hidden field values as empty when adding new item;
*) fixed Graphing and Quickset graphs;
*) fixed default value for disabled wireless EAP methods field;
*) fixed issue with showing non-existing values;
*) fixed managed list category grouping when value is IP with port;
*) fixed missing icon for submenus that are hidden by skin;
*) fixed neighbour table filter "all" storage;
*) fixed saving and restoring of filter comboboxes;
*) fixed skin behavior for "Add" buttons with dropdown;
*) fixed value updating when it is changed and disabled;
*) fixed values with required "&" prefix;
*) fixed wifiwave2 frequency field;
*) show error when not enough space to complete file upload;

If you experience version related issues, then please report them to support@mikrotik.com.

[deniSun]

Και μια που αναφέρθηκαν σε graphing.
Εκείνο το ρημάδι το graphs που δούλευε μια χαρά σε 6.x και με http και με -s,
πόσο δύσκολο είναι να το κάνουν να δουλέψει και με -s στην 7.x.

[billy]

Σαν να δουλεύει η 7.2.3, για την ώρα το 5 GHz WiFi φαίνεται σταθερό. Ρε λες ?

[deniSun]

Σαν να δουλεύει η 7.2.3, για την ώρα το 5 GHz WiFi φαίνεται σταθερό. Ρε λες ?

Γιατί τι πρόβλημα είχες;
Είχα θέμα με την μπάντα των 5 μόνο τον πρώτο καιρό που αγόρασα το RB4011iGS.
Ήταν πρόβλημα που αφορούσε τον επεξεργαστή και έπαιζε σταθερά μόνο με capsman.
Από μια έκδοση της 6 και μετά το έφτιαξαν και από τότε παίζω σταθερά και χωρίς κανένα πρόβλημα συνέχεια με 5
και σε 6 και στην 7.

[BillyVan]

What's new in 7.3 (2022-Jun-06 11:38):

Spoiler:

*) bgp - added "name" parameter for connections;
*) bgp - added initial support for prefix limit;
*) bgp - fixed "keepalive-timeout" value when upgrading from RouterOS v6;
*) bgp - fixed "l2vpn" distribution;
*) bgp - improved stability when editing BGP template;
*) bgp - moved "interface bgp-vpls" menu to "routing bgp vpls";
*) bgp - remove unused commands and parameters;
*) bluetooth - improved long-term service stability;
*) bonding - added "lacp-user-key" setting;
*) bonding - fixed LACP flapping for RB5009 and CCR2004-16G-2S+ devices;
*) bridge - added more details for loop detection warning;
*) bridge - do not set VLAN on inactive port with a "set" command;
*) bridge - fixed TCP, UDP port parsing for loop detect warning;
*) bridge - fixed packet marking for IP/IPv6 firewall;
*) bridge - ignore VLAN tagged BPDU;
*) capsman - fixed bridge disabling when using L2 connection;
*) capsman - fixed loss of manager configuration when "package-path" is set to external disk;
*) capsman - improved traffic processing over CAP communication tunnels:
*) ccr - added "passthrough" flag for interfaces on CCR2004-1G-2XS-PCIe;
*) ccr - added visible "passthrough" flag for interfaces on CCR2004-1G-2XS-PCIe;
*) ccr - improved interface link stability on CCR2004-16G-2S+PC;
*) ccr - usability and stability improvements for passthrough interfaces on CCR2004-1G-2XS-PCIe;
*) cd-install - allow selecting on which drive to install RouterOS;
*) chr - fixed Cloud DDNS update after license renewal;
*) conntrack - limited full Connection Tracking warning to 1 message per minute;
*) console - fixed "terminal inkey" command;
*) crs1xx/2xx - improved system stability during switch reset;
*) defconf - do not add passthrough ports to local bridge on CCR2004-1G-2XS-PCIe;
*) dhcpv4-server - added "age" parameter for dynamic leases;
*) dhcpv4-server - fixed conflicting or declined lease detection when IP pool differs from server's configuration;
*) dhcpv4-server - fixed minor logging typo;
*) dot1x - fixed RADIUS State attribute when client is reauthenticated;
*) dot1x - fixed port based VLAN ID assignment on devices without a switch chip;
*) dot1x - improved server stability when using re-authentication;
*) export - fixed value ID exporting that does not refer to any name;
*) fetch - fixed SFTP upload;
*) fetch - improved full disk detection;
*) filesystem - fixed possible boot failure on RB850Gx2 and RB1100AHx2;
*) filesystem - improved UBIFS stability and data integrity after downgrade to RouterOS v6 and upgrade to RouterOS v7;
*) filesystem - improved long-term filesystem stability and data integrity;
*) gps - added GPS package support for Chateau devices;
*) gps - fixed minor value unit typo;
*) ipsec - fixed IPsec IRQ initialization on startup on TILE;
*) ipsec - fixed printing of active peer statistics;
*) ipv6 - added "ra-preference" parameter support for RA;
*) ipv6 - fixed dynamic non link-local addresses displaying;
*) ipv6 - removed bogus commands from IPv6 neighbors menu;
*) l2tp - added VRF support for L2TP client;
*) l3hw - greatly improved route offloading speed;
*) l3hw - improved offloading for directly connected hosts on CRS305, CRS326-24G-2S+, CRS328, CRS318, CRS310;
*) l3hw - improved offloading in cases of HW table overflow for CRS305, CRS326-24G-2S+, CRS328, CRS318, CRS310;
*) l3hw - improved route table offloading for CRS317, CRS309, CRS312, CRS326-24S+2Q+, CRS354, CRS5xx, CCR2x16 devices;
*) l3hw - log HW routes count and the shortest offloaded subnet prefix if the HW memory gets full;
*) l3hw - offload only main routing table;
*) l3hw - optimized offloading when dealing with large volume of directly connected hosts;
*) l3hw - partial routing table offload for Marvell Prestera DX4000/DX8000 switch chip series;
*) leds - fixed ethernet LED behavior on wAP R ac;
*) leds - fixed wireless related LED behavior with WW2 package;
*) lhgg - improved system stability (introduced in v7.2);
*) lora - do not allow setting non-existing forwarding server;
*) lora - fixed bogus TOO_EARLY errors;
*) lora - removed TX lookup table;
*) lte - added SMS sending support for MBIM protocol;
*) lte - added support for generic PXA1802 based modems;
*) lte - allow only MCC/NMC format in "operator" parameter;
*) lte - clear SIM values when modem in "stopped" state;
*) lte - disabled extended signal info query for Telit LN940 module;
*) lte - disabled wait for LTE auto attach;
*) lte - expose diagnostics channel for all modems;
*) lte - fixed LTE firwmare upgrade on RBLtAP-2HnD with R11e-LTE6;
*) lte - fixed Sierra MC7455 modem initialization;
*) lte - hide slave interfaces from export;
*) lte - improved LTE interface initialization process on LtAP-2HnD;
*) lte - improved stability when configuring multiple APN's at the same time in MBIM mode;
*) lte - improved stability when upgrading LTE firmware on Chateau 5G;
*) mlag - fixed MAC address moving between bridge ports;
*) mpls - do MPLS forwarding for nexthops without mappings;
*) mpls - fixed MPLS MTU and path MTU selection;
*) mpls - fixed MPLS forwarding after any interface configuration parameter is changed;
*) mpls - improved LDP AF selection process and behavior;
*) mpls - made LDP bindings work on PPP interfaces;
*) ntp - do not allow setting port number in "server" parameter;
*) ntp - fixed "use-local-clock" behavior when enabling server;
*) ospf - fixed GRE interface compatibility with OSPF;
*) ospf - ignore instance route when originate-default=if-installed is enabled;
*) ospf - improved stability when enabling or removing interface-template entries;
*) ovpn - adjusted SHA2 authentication algorithm naming to allow legacy OpenVPN implementations to connect;
*) ovpn - fixed hardware offloading support on CHR;
*) ovpn - fixed memory leak on TILE architecture;
*) ovpn - fixed packet processing on MT7621A;
*) ovpn - fixed server instance not responding to incoming connections after reboot on CHR;
*) ovpn - improved Windows client disconnect procedure in UDP mode;
*) ovpn - improved server stability under continous overload;
*) ovpn - improved service stability when outbound packets are blocked by firewall in UDP mode;
*) ovpn - improved service stability when processing frequent disconnects in UDP mode;
*) ovpn - improved stability when forwarding traffic on TILE;
*) ovpn - moved authentication failure messages to "info" logging level;
*) ovpn - reply with the same IP address that the connection was established to;
*) ping - fixed socket allocation after VRF change;
*) port - do not loose "parity" setting;
*) ppp - added support for VRF;
*) ppp - added warning when using prefix length other than /64 for router advertisement;
*) ppp - fixed "remote-ipv6-prefix" parameter unsetting;
*) ppp - fixed active sessions sometimes getting stuck;
*) ppp - fixed issue with multiple active sessions when "only-one" is enabled;
*) profile - added "wireguard" process classificator;
*) profile - added "zerotier" process classificator;
*) qsfp - reset module only when all ports are disabled;
*) queue - allow to set higher limits than 4G;
*) queue - display warning for CAKE type in simple and tree setups when "bandwidth" parameter is configured;
*) queue - improved stability in large list of queue scenarios;
*) rb5009 - fixed 10G linking issues with Intel X520, XXV710 NICs;
*) resource - fixed CPU type display under system resources for ARM and ARM64;
*) romon - fixed VLAN tagged packet processing;
*) route - fixed "nexthop" table printing;
*) route - fixed "table" menu emptying after RouterOS upgrade;
*) route - fixed IPv6 /127 route nexthop resolution;
*) route - fixed static routes in VRF becoming invalid after reboot;
*) route-filter - fixed community matchers;
*) routerboard - fixed USB bus numbering on LtAP and M33G;
*) routerboot - added extra shortcut information on how to boot into etherboot;
*) routerboot - prevent enabling "protected-routerboot" on unsupported factory firmware versions;
*) routerboot - properly reset system configuration when protected bootloader is enabled and reset button used;
*) rsvp-te - improved stability when "Resv" received for non-existing session;
*) sfp - added 2.5Gbps rate for SFP+ and QSFP+ interfaces on 98DXxxxx and 98PX1012 switches (requires disabled auto-negotiation);
*) sfp - hide empty monitor values in console;
*) sfp - improved Q/SFP interface initialization and stability for 98DXxxxx and 98PX1012 switches;
*) sfp - improved QSFP/SFP interface initialization for 98DXxxxx switches;
*) smb - fixed SMB2 file list reporting;
*) snmp - added VRF support (CLI only);
*) snmp - added VRF support;
*) snmp - fixed reported disk size when multiple external disks are attached;
*) snmp - hide Vendor ID in DHCP MIB when branding is present;
*) snmp - report "ifSpeed" as 0 if value out of bounds (use "ifHighSpeed" for high speed interfaces instead);
*) ssh - added AES-GCM cipher support;
*) ssh - fail non-interactive client after first invalid password;
*) ssh - fixed corrupt host key automatic regeneration;
*) ssh - fixed private key usage after downgrade;
*) ssh - removed DSA public key authentication support;
*) supout - added IGMP-Proxy section;
*) supout - added NTP servers section;
*) supout - added PIMSM section;
*) supout - added RIP section;
*) supout - added WireGuard section;
*) supout - added simplified IPv4 and IPv6 routing table prints;
*) switch - added option to match source and destination IP addresses in ARP packets for RB5009 (requires mac-protocol=arp setting);
*) switch - fixed missing stats from traffic-monitor for 98DXxxxx and 98PX1012 switches;
*) system - fixed IP service initialization in VRF after system startup;
*) system - fixed Kernel timer consistency;
*) system - fixed rare partial loss of RouterOS configuration after package upgrade/downgrade/install/uninstall;
*) torch - properly capture all related IPv6 traffic;
*) tr069-client - fixed RPC download of "1 Vendor Configuration File" with branding package;
*) tunnels - improved packet handling over EoIP, IPIP and GRE tunnels;
*) upnp - improved stability when processing incomplete HTTP header;
*) user-manager - added "Acct-Interim-Interval" to predefined attribute list;
*) user-manager - improved stability when received EAP attribute with non-existing state attribute;
*) vpls - fixed "pw-l2mtu" parameter usage;
*) vpls - fixed TE transport path usage after startup;
*) vrrp - fixed learning of bridged local MAC addreses;
*) w60g - improved stability on Cube 60Pro ac and CubeSA 60Pro ac;
*) webfig - properly show all routing table content;
*) wifiwave2 - fixed VLAN tag handling;
*) wifiwave2 - general stability and throughput improvements;
*) winbox - added "Comment" parameter for BGP templates and connections;
*) winbox - added "Default Cost" parameter under "Routing/OSPF/Area" menu;
*) winbox - added "ra-preference" parameter under "IPv6/ND" menu;
*) winbox - added SKID and AKID parameters under "Certificate" menu;
*) winbox - added missing "IBGP", "EBGP", "Limit Exceeded" and "Stopped" parameters under "Routing/BGP/Sessions" menu;
*) winbox - added missing "Keep Sent Attributes" parameter under "Routing/BGP/Connection" menu;
*) winbox - added missing "Scan List" parameter for W60G interfaces;
*) winbox - added missing BGP session commands;
*) winbox - added support for 2.5Gbps and 100Gbps Ethernet speed options;
*) winbox - added warning message for LTE upgrade process;
*) winbox - do not auto start Wireless Sniffer when opened;
*) winbox - do not show "Session Uptime" parameter under "LTE" menu if not supported by modem;
*) winbox - do not show "unknown" area under "Routing/OSPF/LSA" menu;
*) winbox - do not show type value for NXDOMAIN entries under "IP/DNS/Cache" menu;
*) winbox - fixed "Disconnect Timeout" parameter type under "CAPsMAN" menu;
*) winbox - fixed "IP/Cloud" window refreshing after changes are detected;
*) winbox - fixed "Type" values under "IP/Route" menu;
*) winbox - fixed graph drawing in QuickSet;
*) winbox - fixed hex type values under "User Manager" menu;
*) winbox - fixed minor typo in reboot confirmation prompt;
*) winbox - fixed typo in ZeroTier instance title;
*) winbox - made "Interface Templates" table sortable under "Routing/OSPF" menu;
*) winbox - made "MPLS Interface" table sortable under "MPLS" menu;
*) winbox - made 56 the default ping size;
*) winbox - made wireless access list entries sortable when using the wifiwave2 package;
*) winbox - minimal required version is v3.33;
*) winbox - moved "src-address-list" and "dst-address-list" parameters to "General" tab under "IP/Firewall" menu;
*) winbox - moved "src-address-list" and "dst-address-list" parameters to "General" tab under "IPv6/Firewall" menu;
*) winbox - properly clean up SFP module information after it is unplugged;
*) winbox - properly clean up disk after a failed file upload;
*) winbox - properly load band values under "LTE" menu;
*) winbox - removed obsolete "Routing Table" parameter under "IP/Firewall" menu;
*) winbox - show "System/RouterBOARD/Mode Button" on devices that have such feature;
*) winbox - show PVID column by default under "Bridge" menu;
*) winbox - show correct file system type under "System/Disks" menu;
*) winbox - take into account timezone for timed values under "User Manager" menu;
*) wireless - fixed "wmm-support=required" checking;
*) wireless - fixed EAP-TLS authentication;
*) wireless - fixed GUD version in 3gpp information;
*) x86 - added support for Solarflare SFC1920 NIC;
*) x86 - fixed soft-id reading on virtualized x86 installations (introduced in v7.2);
*) x86 - improved support for Intel E810 NIC;
*) zerotier - added support for Controller configuration;

[billy]

Γιατί τι πρόβλημα είχες;
Είχα θέμα με την μπάντα των 5 μόνο τον πρώτο καιρό που αγόρασα το RB4011iGS.
Ήταν πρόβλημα που αφορούσε τον επεξεργαστή και έπαιζε σταθερά μόνο με capsman.
Από μια έκδοση της 6 και μετά το έφτιαξαν και από τότε παίζω σταθερά και χωρίς κανένα πρόβλημα συνέχεια με 5
και σε 6 και στην 7.

Στην 7.1 σε RouterBOARD 962UiGS-5HacT2HnT, είχα προβλημα μόνο σε ενα host (Mac) στο 5 GHz wireless. H συμπεριφορά ήταν περιεργη, δηλαδή το ping μπορεί να έπαιζε σε ενα άλλο μηχάνημα αλλά το ssh όχι, σερφάριζες και έλειπαν εικόνες θα μπορούσες να πείς οτι μιάζει με TCP reset. Ότι άλλο ήταν στο 5 GHz δεν είχε κανένα πρόβλημα. Γύρισες σε 6.x όλα καλά, ξανά σε 5 GHz, το ίδιο ζήτημα. Το έβαζες σε 2.4 όλα καλά.

Μεταξύ 7.1 και 7.2.3 δεν έχω κάνει άλλη αλλαγή ούτε σε configuration ούτε σε θέση στο routerboard ούτε άλλα μηχανήματα.

Τώρα είναι σταθερό (7.2.3) όπως θα έπρεπε. Το μόνο που δεν εχω δοκιμάσει ακομα είναι απο Win 10 backup σε SMB που και εκεί εκανε το ίδιο

[deniSun]

RouterOS version 7.3 has been released in the "v7 stable" channel!

Spoiler:

What's new in 7.3 (2022-Jun-06 11:38):

*) bgp - added "name" parameter for connections;
*) bgp - added initial support for prefix limit;
*) bgp - fixed "keepalive-timeout" value when upgrading from RouterOS v6;
*) bgp - fixed "l2vpn" distribution;
*) bgp - improved stability when editing BGP template;
*) bgp - moved "interface bgp-vpls" menu to "routing bgp vpls";
*) bgp - remove unused commands and parameters;
*) bluetooth - improved long-term service stability;
*) bonding - added "lacp-user-key" setting;
*) bonding - fixed LACP flapping for RB5009 and CCR2004-16G-2S+ devices;
*) bridge - added more details for loop detection warning;
*) bridge - do not set VLAN on inactive port with a "set" command;
*) bridge - fixed TCP, UDP port parsing for loop detect warning;
*) bridge - fixed packet marking for IP/IPv6 firewall;
*) bridge - ignore VLAN tagged BPDU;
*) capsman - fixed bridge disabling when using L2 connection;
*) capsman - fixed loss of manager configuration when "package-path" is set to external disk;
*) capsman - improved traffic processing over CAP communication tunnels:
*) ccr - added "passthrough" flag for interfaces on CCR2004-1G-2XS-PCIe;
*) ccr - added visible "passthrough" flag for interfaces on CCR2004-1G-2XS-PCIe;
*) ccr - improved interface link stability on CCR2004-16G-2S+PC;
*) ccr - usability and stability improvements for passthrough interfaces on CCR2004-1G-2XS-PCIe;
*) cd-install - allow selecting on which drive to install RouterOS;
*) chr - fixed Cloud DDNS update after license renewal;
*) conntrack - limited full Connection Tracking warning to 1 message per minute;
*) console - fixed "terminal inkey" command;
*) crs1xx/2xx - improved system stability during switch reset;
*) defconf - do not add passthrough ports to local bridge on CCR2004-1G-2XS-PCIe;
*) dhcpv4-server - added "age" parameter for dynamic leases;
*) dhcpv4-server - fixed conflicting or declined lease detection when IP pool differs from server's configuration;
*) dhcpv4-server - fixed minor logging typo;
*) dot1x - fixed RADIUS State attribute when client is reauthenticated;
*) dot1x - fixed port based VLAN ID assignment on devices without a switch chip;
*) dot1x - improved server stability when using re-authentication;
*) export - fixed value ID exporting that does not refer to any name;
*) fetch - fixed SFTP upload;
*) fetch - improved full disk detection;
*) filesystem - fixed possible boot failure on RB850Gx2 and RB1100AHx2;
*) filesystem - improved UBIFS stability and data integrity after downgrade to RouterOS v6 and upgrade to RouterOS v7;
*) filesystem - improved long-term filesystem stability and data integrity;
*) gps - added GPS package support for Chateau devices;
*) gps - fixed minor value unit typo;
*) ipsec - fixed IPsec IRQ initialization on startup on TILE;
*) ipsec - fixed printing of active peer statistics;
*) ipv6 - added "ra-preference" parameter support for RA;
*) ipv6 - fixed dynamic non link-local addresses displaying;
*) ipv6 - removed bogus commands from IPv6 neighbors menu;
*) l2tp - added VRF support for L2TP client;
*) l3hw - greatly improved route offloading speed;
*) l3hw - improved offloading for directly connected hosts on CRS305, CRS326-24G-2S+, CRS328, CRS318, CRS310;
*) l3hw - improved offloading in cases of HW table overflow for CRS305, CRS326-24G-2S+, CRS328, CRS318, CRS310;
*) l3hw - improved route table offloading for CRS317, CRS309, CRS312, CRS326-24S+2Q+, CRS354, CRS5xx, CCR2x16 devices;
*) l3hw - log HW routes count and the shortest offloaded subnet prefix if the HW memory gets full;
*) l3hw - offload only main routing table;
*) l3hw - optimized offloading when dealing with large volume of directly connected hosts;
*) l3hw - partial routing table offload for Marvell Prestera DX4000/DX8000 switch chip series;
*) leds - fixed ethernet LED behavior on wAP R ac;
*) leds - fixed wireless related LED behavior with WW2 package;
*) lhgg - improved system stability (introduced in v7.2);
*) lora - do not allow setting non-existing forwarding server;
*) lora - fixed bogus TOO_EARLY errors;
*) lora - removed TX lookup table;
*) lte - added SMS sending support for MBIM protocol;
*) lte - added support for generic PXA1802 based modems;
*) lte - allow only MCC/NMC format in "operator" parameter;
*) lte - clear SIM values when modem in "stopped" state;
*) lte - disabled extended signal info query for Telit LN940 module;
*) lte - disabled wait for LTE auto attach;
*) lte - expose diagnostics channel for all modems;
*) lte - fixed LTE firwmare upgrade on RBLtAP-2HnD with R11e-LTE6;
*) lte - fixed Sierra MC7455 modem initialization;
*) lte - hide slave interfaces from export;
*) lte - improved LTE interface initialization process on LtAP-2HnD;
*) lte - improved stability when configuring multiple APN's at the same time in MBIM mode;
*) lte - improved stability when upgrading LTE firmware on Chateau 5G;
*) mlag - fixed MAC address moving between bridge ports;
*) mpls - do MPLS forwarding for nexthops without mappings;
*) mpls - fixed MPLS MTU and path MTU selection;
*) mpls - fixed MPLS forwarding after any interface configuration parameter is changed;
*) mpls - improved LDP AF selection process and behavior;
*) mpls - made LDP bindings work on PPP interfaces;
*) ntp - do not allow setting port number in "server" parameter;
*) ntp - fixed "use-local-clock" behavior when enabling server;
*) ospf - fixed GRE interface compatibility with OSPF;
*) ospf - ignore instance route when originate-default=if-installed is enabled;
*) ospf - improved stability when enabling or removing interface-template entries;
*) ovpn - adjusted SHA2 authentication algorithm naming to allow legacy OpenVPN implementations to connect;
*) ovpn - fixed hardware offloading support on CHR;
*) ovpn - fixed memory leak on TILE architecture;
*) ovpn - fixed packet processing on MT7621A;
*) ovpn - fixed server instance not responding to incoming connections after reboot on CHR;
*) ovpn - improved Windows client disconnect procedure in UDP mode;
*) ovpn - improved server stability under continous overload;
*) ovpn - improved service stability when outbound packets are blocked by firewall in UDP mode;
*) ovpn - improved service stability when processing frequent disconnects in UDP mode;
*) ovpn - improved stability when forwarding traffic on TILE;
*) ovpn - moved authentication failure messages to "info" logging level;
*) ovpn - reply with the same IP address that the connection was established to;
*) ping - fixed socket allocation after VRF change;
*) port - do not loose "parity" setting;
*) ppp - added support for VRF;
*) ppp - added warning when using prefix length other than /64 for router advertisement;
*) ppp - fixed "remote-ipv6-prefix" parameter unsetting;
*) ppp - fixed active sessions sometimes getting stuck;
*) ppp - fixed issue with multiple active sessions when "only-one" is enabled;
*) profile - added "wireguard" process classificator;
*) profile - added "zerotier" process classificator;
*) qsfp - reset module only when all ports are disabled;
*) queue - allow to set higher limits than 4G;
*) queue - display warning for CAKE type in simple and tree setups when "bandwidth" parameter is configured;
*) queue - improved stability in large list of queue scenarios;
*) rb5009 - fixed 10G linking issues with Intel X520, XXV710 NICs;
*) resource - fixed CPU type display under system resources for ARM and ARM64;
*) romon - fixed VLAN tagged packet processing;
*) route - fixed "nexthop" table printing;
*) route - fixed "table" menu emptying after RouterOS upgrade;
*) route - fixed IPv6 /127 route nexthop resolution;
*) route - fixed static routes in VRF becoming invalid after reboot;
*) route-filter - fixed community matchers;
*) routerboard - fixed USB bus numbering on LtAP and M33G;
*) routerboot - added extra shortcut information on how to boot into etherboot;
*) routerboot - prevent enabling "protected-routerboot" on unsupported factory firmware versions;
*) routerboot - properly reset system configuration when protected bootloader is enabled and reset button used;
*) rsvp-te - improved stability when "Resv" received for non-existing session;
*) sfp - added 2.5Gbps rate for SFP+ and QSFP+ interfaces on 98DXxxxx and 98PX1012 switches (requires disabled auto-negotiation);
*) sfp - hide empty monitor values in console;
*) sfp - improved Q/SFP interface initialization and stability for 98DXxxxx and 98PX1012 switches;
*) sfp - improved QSFP/SFP interface initialization for 98DXxxxx switches;
*) smb - fixed SMB2 file list reporting;
*) snmp - added VRF support (CLI only);
*) snmp - added VRF support;
*) snmp - fixed reported disk size when multiple external disks are attached;
*) snmp - hide Vendor ID in DHCP MIB when branding is present;
*) snmp - report "ifSpeed" as 0 if value out of bounds (use "ifHighSpeed" for high speed interfaces instead);
*) ssh - added AES-GCM cipher support;
*) ssh - fail non-interactive client after first invalid password;
*) ssh - fixed corrupt host key automatic regeneration;
*) ssh - fixed private key usage after downgrade;
*) ssh - removed DSA public key authentication support;
*) supout - added IGMP-Proxy section;
*) supout - added NTP servers section;
*) supout - added PIMSM section;
*) supout - added RIP section;
*) supout - added WireGuard section;
*) supout - added simplified IPv4 and IPv6 routing table prints;
*) switch - added option to match source and destination IP addresses in ARP packets for RB5009 (requires mac-protocol=arp setting);
*) switch - fixed missing stats from traffic-monitor for 98DXxxxx and 98PX1012 switches;
*) system - fixed IP service initialization in VRF after system startup;
*) system - fixed Kernel timer consistency;
*) system - fixed rare partial loss of RouterOS configuration after package upgrade/downgrade/install/uninstall;
*) torch - properly capture all related IPv6 traffic;
*) tr069-client - fixed RPC download of "1 Vendor Configuration File" with branding package;
*) tunnels - improved packet handling over EoIP, IPIP and GRE tunnels;
*) upnp - improved stability when processing incomplete HTTP header;
*) user-manager - added "Acct-Interim-Interval" to predefined attribute list;
*) user-manager - improved stability when received EAP attribute with non-existing state attribute;
*) vpls - fixed "pw-l2mtu" parameter usage;
*) vpls - fixed TE transport path usage after startup;
*) vrrp - fixed learning of bridged local MAC addreses;
*) w60g - improved stability on Cube 60Pro ac and CubeSA 60Pro ac;
*) webfig - properly show all routing table content;
*) wifiwave2 - fixed VLAN tag handling;
*) wifiwave2 - general stability and throughput improvements;
*) winbox - added "Comment" parameter for BGP templates and connections;
*) winbox - added "Default Cost" parameter under "Routing/OSPF/Area" menu;
*) winbox - added "ra-preference" parameter under "IPv6/ND" menu;
*) winbox - added SKID and AKID parameters under "Certificate" menu;
*) winbox - added missing "IBGP", "EBGP", "Limit Exceeded" and "Stopped" parameters under "Routing/BGP/Sessions" menu;
*) winbox - added missing "Keep Sent Attributes" parameter under "Routing/BGP/Connection" menu;
*) winbox - added missing "Scan List" parameter for W60G interfaces;
*) winbox - added missing BGP session commands;
*) winbox - added support for 2.5Gbps and 100Gbps Ethernet speed options;
*) winbox - added warning message for LTE upgrade process;
*) winbox - do not auto start Wireless Sniffer when opened;
*) winbox - do not show "Session Uptime" parameter under "LTE" menu if not supported by modem;
*) winbox - do not show "unknown" area under "Routing/OSPF/LSA" menu;
*) winbox - do not show type value for NXDOMAIN entries under "IP/DNS/Cache" menu;
*) winbox - fixed "Disconnect Timeout" parameter type under "CAPsMAN" menu;
*) winbox - fixed "IP/Cloud" window refreshing after changes are detected;
*) winbox - fixed "Type" values under "IP/Route" menu;
*) winbox - fixed graph drawing in QuickSet;
*) winbox - fixed hex type values under "User Manager" menu;
*) winbox - fixed minor typo in reboot confirmation prompt;
*) winbox - fixed typo in ZeroTier instance title;
*) winbox - made "Interface Templates" table sortable under "Routing/OSPF" menu;
*) winbox - made "MPLS Interface" table sortable under "MPLS" menu;
*) winbox - made 56 the default ping size;
*) winbox - made wireless access list entries sortable when using the wifiwave2 package;
*) winbox - minimal required version is v3.33;
*) winbox - moved "src-address-list" and "dst-address-list" parameters to "General" tab under "IP/Firewall" menu;
*) winbox - moved "src-address-list" and "dst-address-list" parameters to "General" tab under "IPv6/Firewall" menu;
*) winbox - properly clean up SFP module information after it is unplugged;
*) winbox - properly clean up disk after a failed file upload;
*) winbox - properly load band values under "LTE" menu;
*) winbox - removed obsolete "Routing Table" parameter under "IP/Firewall" menu;
*) winbox - show "System/RouterBOARD/Mode Button" on devices that have such feature;
*) winbox - show PVID column by default under "Bridge" menu;
*) winbox - show correct file system type under "System/Disks" menu;
*) winbox - take into account timezone for timed values under "User Manager" menu;
*) wireless - fixed "wmm-support=required" checking;
*) wireless - fixed EAP-TLS authentication;
*) wireless - fixed GUD version in 3gpp information;
*) x86 - added support for Solarflare SFC1920 NIC;
*) x86 - fixed soft-id reading on virtualized x86 installations (introduced in v7.2);
*) x86 - improved support for Intel E810 NIC;
*) zerotier - added support for Controller configuration;

Σεντόνι.

Off Topic

Color/font γιατί έβαλες;

[BillyVan]

Απ οτι διαβασα δεν εχουν προσθεσει / διορθωσει κατι παραπανω απ τις rc1, rc2, beta40....

Ειναι το αθροισμα ολων και γι αυτο το σεντονι.

Το ειδα οτι βγηκε χαλια αλλα ενα copy / paste εκανα στο σποιλερ μεσα και εγινε μου.ι καπελλο χαχαχα.

Διορθωθηκε...

[deniSun]

Ειναι το αθροισμα ολων.

Λογικό.

- - - Updated - - -

7.4beta2 changelog:

Spoiler:

*) api - fixed comma encoding within URL when using the ".proplist" argument;
*) bridge - properly process IPsec decapsulated packets through the firewall when the "use-ip-firewall" option is enabled;
*) capsman - require a unique name for configuration and configuration pre-sets;
*) cloud - print critical log message when system clock gets synchronised;
*) console - added ":retry" command;
*) console - fixed situation when print output was not consistent;
*) dns - convert the domain name to lowercase before matching regex;
*) e-mail - added VRF support (CLI only);
*) filesystem - fixed repartition on RB5009 series devices;
*) firewall - added "srcnat" and "dstnat" flags to IPv6/Firewall/Connection table;
*) firewall - added support for IPv6/Firewall/NAT action=src-nat rules (CLI only);
*) firewall - fixed IPv6 NAT functionality when processing GRE traffic on TILE devices;
*) firewall - fixed IPv6/Firewall/RAW functionality;
*) firewall - include "connection-mark", "connection-state", and "packet-mark" when packet logging is enabled;
*) firewall - properly handle interface matcher when VRF interface is specified;
*) hotspot - fixed ARP resolution for clients when address pool is specified on the server;
*) hotspot - fixed Walled Garden entries with action=deny;
*) ipv6 - fixed system stability when adding/removing IPv6 address;
*) ldp - correctly handle AFI selection for usage on dual-stack peers;
*) lte - request connect with the same IP type as in LTE attach status for MBIM;
*) lte - fixed Telit AT interface numbering;
*) lte - improved LTE interface detection for LtAP-2HnD devices;
*) lte - keep MBIM working even if AT channel fails to respond in the initialisation stage;
*) mmips - improved USB device detection after system bootup;
*) mpls - fixed VPLS functionality when PW peer is an immediate neighbor;
*) ovpn - use selected cipher by default when the server does not provide "cipher" option;
*) pimsm - improved system stability when changing configuration;
*) ppp - properly try to use different authentication algorithms when Conf-Rej is received during the LCP phase;
*) quickset - specify the "in-interface-list=WAN" attribute on firewall rules created through "Port Mapping";
*) route - added option to join static IGMP and MLD groups (available in "/routing/gmp" menu, CLI only)
*) route - fixed false route type detection as blackhole;
*) route - provide more detailed information about prefixes when using "discourse" tool;
*) routing - moved "/interface bgp vpls" to "/routing bgp vpls" menu;
*) routing-filter - fixed regexp community matcher;
*) ssh - disable ssh-rsa when strong-crypto=yes and use rsa-sha2-sha256;
*) ssh - implemented "server-sig-algs" extension in order to improve rsa-sha2-sha256 support;
*) switch - disabled second CPU core for CRS328-24P-4S+ device in order to improve SFP+ link stability;
*) vxlan - allow to specify MAC address manually;
*) webfig - updated WebFig HTML files with the new MikroTik logo and removed Telnet option from index page;
*) webfig - updated link to the WinBox executable;
*) webfig - updated link to the documentation;
*) wifiwave2 - fixed "frequency-scan" functionality (introduced in v7.3);
*) winbox - add a log and log-prefix options to IPv6 firewall NAT and mangle rules;
*) winbox - fixed IP/Route and IPv6/Route OSPF type value;
*) winbox - removed unused "Apply Changes" button from BGP sessions menu;
*) wireguard - fixed system stability when adding/removing WireGuard interface;
*) wireless - fixed possible traffic flooding to WDS clients when using Nv2 and multicast helper;
*) x86 - fixed keep old configuration functionality during x86 setup installation;
*) x86 - improved log warning message on failed downgrade attempt;
*) x86 - removed "hdd-model" information from installation screen;